Unipro UniGo 7006 User Manual


TurnonUniGo
YouturnonUniGobypressingtheMODEbuttonshortlyorby
startingtheengine.
Note!ItisrecommendtousetheMODEbuttontoturnonUniGoa
whilebeforestartingtheengine,thatwayUniGowillfindsome
satellitesbeforeyougooutontheracetrack.[6005/8005]

Setupmode
TherearealotofsettingsyoucanchangetocustomizeyourUniGo.
InthisguideIwillgothrusomebasicsettings.Youwillfindallthe
settingsunderthesetupmenuanditssubmenus.
 TurnonUniGo
 FromtheMAINMENUselectSETUPMENU.
 Selectthe<submenuoption>(seebelow)
TrackMenu
Thismenuoptioncontainsallthesettingsregardingtheracetrack,
e.g.thenameofthetrack,thereceiveryouareusingetc.
Seeseparateguide“UniproUniGoQuickGuide#2”.
KartMenu
Thismenuoptioncontainsallthesettingsregardingthekart.The
settingsIwanttohighlightare:
 WHEELSIZE
Ifyouareusingafrontwheelorarearaxlespeedsensoryou
needtosetthecircumferenceofthewheeltogetthecorrect
speedanddistance.IfnotsettheoptiontoOFF.
 NAME/TYPE
Hereyousetthenameofyourkart/class.Whenyouimport
datatoOffCamberDatathissettingwillautomaticallyfillthe
optionKart.
 WHEELMAGNETS
Ifyouareusingafrontwheelorarearaxlespeedsensoryou
needtosetthenumberofmagnetsonthesensordisc.
ENGINEMENU
Thismenuoptioncontainsallthesettingsregardingtheengine.The
settingsIwanttohighlightare:
 RPMFACTOR
SettheinputandfactorfortheRPMsensor.Themostcommon
settingforkartingis“RPMinputx1”.
 RPMSHIFT
SettheRPMtoturnontheLEDwhenit’stimetoshiftgear.If
youuseanon‐shifterkart,setthissettingtoahighervaluethen
themaxRPMofyourenginetoturntheLEDoff.
 RPMBARGRAPHMAX
SetthemaxRPMforthebargraph.Setthissettingtothemax
RPMofyourengine.
Note!ThisgraphisusedontheRunMode2screens.
UNIGOMENU
ThismenuoptioncontainsallthesettingsregardingtheUniGounit.
ThesettingsIwanttohighlightare:
 LANGUAGE
Setthedisplaylanguage.UniGosupportsalotoflanguage.
 SETUPSCREENS…
Onthisoptionyouselectthechannels/sensorsyouwantto
showintherunmode.UniGohavethreerunmodescreens(see
RunModeformoreinformationaboutthisscreens).
Note!UseMODEbuttontobrowsebetweenthescreens.Use
UP/DOWNbuttontobrowsebetweenchannel/sensorpositions
onthescreen.UseOK/SELECTbuttontoselecta
channel/sensor.
Note!Onthesamerow,ifyouonlyselectonechannel/sensor
andtheotherisnone.Theselectedchannel/sensorwillbe
centeredontherunmodescreen.
 WARNINGLEDSETUP…
UnderthisoptionyoucancontrolthefiveLEDsatthetopof
UniGo.Youfirstselectthewarningled1‐5,youthenselectthe
channel/sensoryouwanttoconnecttothisLED,andlastyou
decideiftheLEDshouldflashorhaveaconstantlightforthe
MINand/orMAXvalueofthechannel/sensor.E.g.youcanhave
oneledflashingifthewatertempistolowandanotherifitis
toohighorthesameLEDlightisavalueisinside/outsidetwo
values.
 SETTIME…
Underthisoptionyousetthetime,12/24hourclockandtime
zonecorrection.IfyouusingaGPS[6005/8005]thetimeis
automaticallyset.
 SETDATE…
Underthisoptionyousetthedateanddateformat.Ifyouusing
aGPS[6005/8005]thedateisautomaticallyset.
DriverMenu
Thismenuoptioncontainsallthesettingsregardingthedriver.
 NAME
Enterthenameofthedriver

RUNMODE
Therunmodeisthescreenthatthedriverseewhendriving.When
youstarttheengineUniGoautomaticallyopenstherunmode.
Youcanalsoopenitmanually:
 TurnonUniGo
 FromMAINMENUselectRUNMODE.
Inrunmodeyouhavetheoptiontoselectbetweenthreemode
screens,usetheMODEbuttontobrowsebetweenthescreens.
Onthisthreescreensyouhavesomefixeddatae.g.laptimeandlap
number.Youalsohavetheoptiontoselectchannels/sensorsofyour
choice(seeaboveSETUPSCREENSandRPMBargraphMax).
Thethreescreensare:
 RunMode1(Isusedtoshowthemaximumnumberofdata)
Itwillshowthelaptime,lapnumberandbestlaptimeatthe
top.Andupto4channels/sensorsofyourchoice.
 RunMode2(Isprimarilyusedforshifterkarts)
ItwillshowtheRPMbargraph,laptime,gearindicator,lap
numberandbestlaptimeatthetop.Andupto2
channels/sensorsofyourchoice.
 RunMode3(Isforpermanentlydataand2channels/sensor)
Atthetopitwillshowthebestlapandit’slapnumber
permanently,underthatthelastlaptimeandcurrentlap
number.Itwillshow2channels/sensorsofyourchoice,andat
thebottomlineitwillpermanentlyshowthelastlapmaximum
valueforyour2selectedchannels/sensors.

AnalyzeMenu
TheAnalyzemenuareaquickanalyzefunction.Ifyouwanttodoa
deeperanalysis,youneedtodownloadtheruntoOffCamberData.
Toopenanalyzemenu
 TurnonUniGo
 FromtheMAINMENUselectANALYZEMENU
TheAnalyzemenuhavefoursubmenus.
 Selectthesessionyouwanttoanalyze
 Analyzelapandsplittimes
 Analyzeminimumandmaximumvalue
 Analyzecountersandtimers(willnotbecoveredinthisguide).
Selectthesessionyouwanttoanalyze
Bydefaultthelatestsessionisautomaticallyselectedafterarun.If
youwanttoanalyzeearliersessionsyouselectthatsessionunder
thismenuoption.Thelatest32sessionarelistedinreversedorder
withthelatestfirst.
Note!ItisrecommendedtosetupUniGowithdate,time,trackand

Unipro UniGo 7006 Specifications

General

Brand	Unipro
Model	UniGo 7006
Category	Measuring Instruments
Language	English

Summary

Setup Mode

Kart Menu Configuration

Settings for the kart, including wheel size, name, type, and sensor magnets.

Wheel Size Setup

Set wheel circumference for accurate speed and distance readings.

Kart Name and Type

Set kart name/class for data import and automatic filling in Off Camber Data.

Wheel Magnets Setup

Set the number of magnets on the sensor disc for speed sensing.

Engine Menu Settings

RPM Factor Configuration

Set the input and factor for the RPM sensor. Default is 'RPM input x1'.

RPM Shift Indicator

Set RPM to activate the LED shift indicator. Higher value turns LED off for non-shifter karts.

RPM Bargraph Maximum

Set the maximum RPM for the bargraph display on Run Mode 2 screens.

UniGo Unit Settings

Language Selection

Set the display language for the UniGo unit.

Run Mode Screen Setup

Select channels/sensors to display on the three run mode screens.

Warning LED Configuration

Control five LEDs for warnings: select channel, flash/constant, MIN/MAX value.

Time and Time Zone Setup

Set the time (12/24 hour) and time zone correction. GPS auto-sets time.

Date Setup

Set the date and date format. GPS auto-sets date.

Driver Menu Setup

Driver Name Entry

Enter the name of the driver.

Run Mode Screens

Run Mode 1 Data Display

Shows lap time, number, best lap, and up to 4 selected channels/sensors.

Run Mode 2 (Shifter Kart)

Shows RPM bargraph, lap time, gear, and up to 2 selected channels/sensors.

Run Mode 3 (Permanent Data)

Shows best lap, last lap times, and 2 channels/sensors with max values.

Analyze Menu

Analyze Lap and Split Times

Analyze lap and split times, including best lap, theoretical lap, and rolling best time.

Best Lap Min/Max Values

Display Min and Max values for selected channels for the best lap.

Bar Chart Lap Analysis

Visualize lap times with a bar chart, showing lap number, time, and diff to best lap.

Customize Owner Name

Owner Name Setup

Create a text file with owner name and upload via USB for startup screen.

Troubleshooting

RPM Signal Interference

Diagnose and resolve RPM signal interference issues by checking wire routing and signal strength.

UniGo Crashes/Hangs

Minimize crashes by using a LiPo battery or DC/DC converter.

Firmware Update

Update via USB Flash Key

Update firmware by copying the file to the USB key's Firmware folder.

Update via USB Cable

Update firmware by copying the file to the UniGo's Firmware folder via USB cable.