Universal Security Instruments SS-795 User Manual

Page 2
RECOMMENDED LOCATION OF ALARMS
• Locate the first smoke alarm in the immediate area of the bedrooms. Try to protect the escape
route as the bedrooms are usually farthest from an exit. If more than one sleeping area exists,
locate additional smoke alarms in each sleeping area. If a hall is more than 40 feet (12 meters)
long, install a smoke alarm at each end.
• Locate additional smoke alarms to protect any stairway as stairways act like chimneys for
smoke and heat.
• Locate at least one smoke alarm on every floor level.
• Locate a smoke alarm in any area where a smoker sleeps or where electrical appliances are
operated in sleeping areas.
• Smoke, heat and other combustion products rise to the ceiling and spread horizontally. Mounting
the smoke alarm on the ceiling in the center of the room places it closest to all points in the room.
Ceiling mounting is preferred in ordinary residential construction. However, in mobile homes, wall
mounting on an inside partition is preferred to avoid the thermal barrier that may form at the
ceiling.
• When mounting smoke alarm on the ceiling, locate it a minimum of 4" (10cm) from a side wall
or corner (see Diagram A).
• When mounting smoke alarm on a wall, if local codes allow, use an inside wall with the top edge
of the smoke alarm a minimum of 4" (10cm) and a maximum of 12" (30.5cm) below the ceiling/
wall intersections (See Diagram A).
Sloped Ceilings (Peaked Ceilings):
Smoke alarms or smoke detectors mounted on a peaked ceiling shall be located within 36 in. (914 mm) horizontally
of the peak, but not closer than 4 in. (102 mm) vertically to the peak.
Sloped Ceilings (Shed Ceilings):
Smoke alarms or smoke detectors mounted on a sloped ceiling having a rise greater than 1 ft. in 8 ft. (1 m in 8
m) horizontally shall be located within 36 in. (914 mm) of the high side of the ceiling, but not closer than 4 in. (102
mm) from the adjoining wall surface.
Tray-Shaped Ceilings:
Smoke Alarms or smoke detectors shall be installed on the highest portion of the ceiling or on the sloped portion
of the ceiling within 12 in. (305 mm) vertically down from the highest point.
Mobile Home Installation:
For minimum protection, smoke alarms should be installed in compliance with H.U.D. Manufactured Home
Construction Safety Standards, Title 24 CFR, Section 3280.208 and Section 3282. For additional protection, see
Single Story Residence smoke alarm requirements/recommendations for Existing Homes and New Construction
Homes.
Note: For mobile homes built before 1978, install smoke alarms on inside walls between 4” and 12” from the
ceiling (older mobile homes have little or no insulation in the ceiling). This is especially important if the ceiling
is unusually hot or cold.
Install a smoke alarm inside each bedroom and in the hallway outside each separate sleeping area.
Existing Homes:
The NFPA requires a smoke alarm on every level and outside each sleeping area in existing construction. An
existing household with one level and one sleeping area is required to have one smoke alarm.
New Construction Homes and Manufactured Homes:
The NFPA requires AC-powered, interconnected smoke alarms to be installed inside each bedroom, outside each
bedroom area, and on every level of the home. They also require a minimum of two AC-powered, interconnected
smoke alarms in any new construction home.

Universal Security Instruments SS-795 Specifications

General

Brand	Universal Security Instruments
Model	SS-795
Category	Smoke Alarm
Language	English

Summary

Smoke Alarm Limitations and Functions

Dual Alarm Technology

Compares ionization and photoelectric smoke detection technologies for reliability and response.

Operational Dependencies and Failures

Covers limitations related to power, smoke detection, audibility, and potential for false alarms.

Lifespan and Maintenance

Emphasizes the unit's limited lifespan and the necessity for regular testing and maintenance.

Recommended Location of Alarms

General Placement Guidelines

Advises on placing alarms near sleeping areas, stairways, and on every floor for optimal protection.

Mounting Specifications

Details ceiling and wall mounting distances from walls and ceilings as per guidelines.

Home Construction Requirements

Outlines NFPA requirements for existing and new construction homes and manufactured homes.

Specialized Ceiling and Mobile Home Locations

Provides guidance for sloped, tray-shaped ceilings and specific recommendations for mobile homes.

Installation and Safety Precautions

Avoid These Locations

Lists specific areas to avoid for proper smoke alarm function, such as garages or high humidity zones.

Electrical Shock Hazard

Warns about the danger of electrical shock during installation and the need to turn off power.

Tamper Locking Pin

Explains the function of the tamper pin for deterring unauthorized removal of the alarm.

Wiring and Interconnection

Wire Connections

Details the proper connections for AC power (black, white) and interconnect (yellow) wires.

Interconnected Unit Capabilities

Explains how interconnected alarms provide earlier warning and lists compatible models.

Multiple Unit Installation Setup

Illustrates the wiring setup for connecting multiple smoke alarm units for enhanced detection.

Operation, Testing & Maintenance

Normal Operation and Alarm Signals

Describes the unit's standby, local alarm, and remote alarm conditions indicated by LEDs and sound.

Testing and False Alarm Silence

Provides instructions for testing the alarm via the built-in switch and using the silence feature.

Maintenance and Battery Replacement

Guides on cleaning the unit and replacing the 9-volt backup battery with recommended types.

Develop and Practice a Plan of Escape

Basics of Escape Plan

Offers steps for creating and practicing a home fire escape plan, including meeting points.

What to Do When the Alarm Sounds

Provides critical actions to take, such as immediate evacuation and contacting the fire department.

NFPA Required Protection

Details National Fire Protection Association (NFPA) Standard 72 requirements for smoke detection.

Universal Five Year Limited Warranty

Warranty Coverage and Exclusions

Outlines the five-year warranty, what it covers, and common exclusions like misuse or improper installation.

Repair or Replacement Procedure

Details the process for returning a defective product for repair or replacement, including costs.