UWS DS-18 - User Manual

UWSTA.COM
•
NEED ASSISTANCE?
•
87 7. 2 87.8 6 3 4
•
RA
•
PAGE 1
INSTALLATION MANUAL
Parts List
1 Drawer truck tool box
2 Key
4 Hex bolt, 1/4" x 1-1/4"
8 Flat washer, 1/4"
4 Nylock nut, 1/4"
INSTALLATION MANUAL
Tools Required
Drill Drill bit set
Ratchet Socket set
Tape measure --
Level of Difficulty
Easy
Representative Product Photos (your specific box may vary in style, size or finish)
DRAWER TRUCK
TOOL BOX
Maintenance
For polished, gloss and other smooth
finishes, polish may be used to clear
small scratches and scuffs on the finish.
Mild automotive detergent may be used to
clean the product. Do not use dish detergent,
abrasive cleaners, abrasive pads, wire
brushes or other similar products that
may damage the finish.
DANGER
Danger of explosion. Do not use this product for storing or transporting flammables,
explosives, hazardous materials or hazardous waste, such as containers of gasoline,
solvents, gun powder, dynamite, propane tanks, acetylene tanks and cutting torches.
WARNING
Never exceed the vehicle manufacturer's recommended capacity.
Do not interfere with factory-installed safety equipment.
NOTICE
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To help prevent damage to the product or vehicle, refer to the torque
specifications when securing hardware during the installation process.
Do not use this product for purposes other than those
for which they were designed. Never modify this product.
Consult your dealer if you have any questions regarding
the installation, operation, use and limits of this product.
Treat or seal all fasteners and exposed metal in any
holes drilled in vehicle to prevent corrosion.
Torque Specifications*
Metric
M6 bolt 3 ft-lbs.
M8 bolt 7 ft-lbs.
M10 bolt 16 ft-lbs.
M12 bolt 28 ft-lbs.
SAE
1/4" bolt 3 ft-lbs.
5/16" bolt 7 ft-lbs.
3/8" bolt 16 ft-lbs.
7/16" bolt 20 ft-lbs.
1/2" bolt 28 ft-lbs.
* Above specifications are general guidelines.
If purchasing hardware use the torque
specifications provided with that hardware.
Product Registration and Warranty
CURT Group stands behind our products with industry-leading warranties.
Provide feedback and help us to improve our products by registering your purchase at:
warranty.curtgroup.com/surveys

Summary

Important Installation Notices

Safety Warnings

Critical safety information regarding explosion hazards and vehicle capacity.

General Installation Advice

Read all instructions thoroughly, use proper tools, prevent damage, and do not modify the product.

Product Maintenance and Registration

Maintenance Guidelines

Instructions for cleaning and maintaining the product's finish to prevent damage.

Product Registration and Warranty

Information on registering your purchase and understanding warranty coverage.

Installation Steps

Step 1: Mounting Procedure

Detailed instructions for drilling holes and securing the tool box to the mounting surface.

Step 2: Final Checks and Recommendations

Post-installation checks for security and advice on periodic inspections.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

This document provides an installation manual for a UWS Drawer Truck Tool Box, designed for easy installation.

Function Description

The UWS Drawer Truck Tool Box is a storage solution intended for installation in a truck bed. It features multiple drawers for organizing tools and other items. The installation process involves securing the tool box to the truck bed using bolts, washers, and nylock nuts.

Important Technical Specifications

The manual lists specific hardware components for installation:

• Parts List:
  • 1 Drawer truck tool box
  • 2 Keys
  • 4 Hex bolts, 1/4" x 1-1/4"
  • 8 Flat washers, 1/4"
  • 4 Nylock nuts, 1/4"
• Tools Required:
  • Drill
  • Drill bit set
  • Ratchet
  • Socket set
  • Tape measure
• Torque Specifications (General Guidelines):
  • Metric Bolts:
    • M6 bolt: 3 ft-lbs.
    • M8 bolt: 7 ft-lbs.
    • M10 bolt: 16 ft-lbs.
    • M12 bolt: 28 ft-lbs.
  • SAE Bolts:
    • 1/4" bolt: 3 ft-lbs.
    • 5/16" bolt: 7 ft-lbs.
    • 3/8" bolt: 16 ft-lbs.
    • 7/16" bolt: 20 ft-lbs.
    • 1/2" bolt: 28 ft-lbs.
  • Note: If purchasing hardware, use the torque specifications provided with that hardware.

Usage Features

The tool box is designed for secure storage in a truck bed. The installation process ensures a stable mounting.

• Installation Steps:
  1. Preparation: Before drilling, users must check under the truck bed to avoid puncturing or obstructing brake/fuel lines, electrical wires, or fuel tanks. Special care is needed for fasteners near the fuel tank to prevent damage during a collision.
  2. Positioning: Remove the bottom two drawers from the tool box, place the tool box on the mounting surface, and mark the mounting surface using the guide holes on the inside of the tool box.
  3. Drilling: Drill 1/4" holes at the marked locations.
  4. Securing: Align the holes in the tool box with the drilled holes in the mounting surface. Insert one 1/4" hex bolt and a flat washer from the inside of the tool box. Secure it with another flat washer and a nylock nut on the underside of the mounting surface. Repeat for all mounting holes and tighten all hardware.
  5. Reassembly: Re-install the bottom two drawer slides.
• Safety Warnings:
  • DANGER (Explosion Risk): Do not use this product for storing or transporting flammables, explosives, hazardous materials, or hazardous waste (e.g., gasoline, solvents, gunpowder, dynamite, propane tanks, acetylene tanks, cutting torches).
  • WARNING (Vehicle Capacity): Never exceed the vehicle manufacturer's recommended capacity.
  • WARNING (Safety Equipment): Do not interfere with factory-installed safety equipment.
  • CAUTION (Security): Ensure all knobs, bolts, screws, straps, and locks are firmly secured before every trip. Periodically re-tighten and inspect all components for signs of wear, corrosion, and fatigue.
  • CAUTION (Mounting Hardware): With the drawer tool box installed, periodic inspections should be performed to ensure all mounting hardware remains tight.
• General Notices:
  • Read all instructions thoroughly before installation.
  • Proper tools improve installation quality and reduce time.
  • Refer to torque specifications when securing hardware to prevent damage.
  • Do not use this product for purposes other than those for which it was designed.
  • Never modify this product.
  • Consult a dealer for questions regarding installation, operation, use, and limits.
  • Treat or seal all fasteners and exposed metal in any holes drilled in the vehicle to prevent corrosion.

Maintenance Features

Proper maintenance is crucial for the longevity and appearance of the UWS Drawer Truck Tool Box.

• Finish Maintenance:
  • For polished, gloss, and other smooth finishes, polish can be used to clear small scratches and scuffs.
  • Mild automotive detergent may be used to clean the product.
  • Avoid: Dish detergent, abrasive cleaners, abrasive pads, wire brushes, or similar products that may damage the finish.
• Product Registration and Warranty:
  • CURT Group provides industry-leading warranties.
  • Users can register their purchase at warranty.curtgroup.com/surveys to provide feedback and help improve products.

UWS DS-18 Specifications

General

Brand	UWS
Model	DS-18
Category	Automobile Accessories
Language	English