VALBERG BM 1993 - User Manual

2020-02
USER MANUAL
SAFETY CABINET
BM 1993
Before you start
The lock can handle two opening codes: Master code and User code 2. The Master code is set from the factory
to 123456. User code 2 is submissive to the Master code and is not included in the Factory settings. The Master
code must be changed before you can program User code 2.
The lock signals with a beep and a flash with every correct action, and it signals with a long beep and red flash
with every wrong action.
Always program the lock with an open door and check the result before you close the door.
Open the lock
1. Push ”ON”. The lock signals with a beep and the green light comes on.
2. Enter Master code (Factory Master code. 123456) or User code 2. The lock signals with a LED flash.
3. Turn the handle clockwise within 4 seconds.
Open the safe
1. Close the door completely. Make sure nothing gets jammed.
2. Turn the handle anticlockwise.
Change Master code
1. Open the lock.
2. Push ”ON” and then ”ENTER”.
3. Push 1 and then “ENTER”.
4. Enter the current Master code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit code again and then “ENTER”. The lock signals with 2 beeps and LED flashes.
Activate User Code 2
1. Open the lock.
2. Push ”ON” and then ”ENTER”.
3. Push 2 and then “ENTER”.
4. Enter the current Master code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit User code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit User code again and then “ENTER”. The lock signals with 2 beeps and LED flashes.
Change User code 2 without Master code
1. Open the lock.
2. Push ”ON” and then ”ENTER”.
3. Push 3 and then “ENTER”.
4. Enter the current Master code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
5. Enter a new 6-8-digit User code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
6. Enter the new 6-8-digit User code again and then “ENTER”. The lock signals with 2 beeps and LED flashes
Delete User code 2
1. Open the lock.
2. Push ”ON” and then ”ENTER”.
3. Push 0 and then “ENTER”.
4. Enter the current Master code and then “ENTER”. The lock signals with 2 beeps and LED flashes.
See other side, how to change battery

Summary

Getting Started with the Safety Cabinet Lock

General Lock Operation

Understand lock signals, factory settings, and pre-operation checks for programming.

Lock Operation Procedures

Open the Lock

Steps to unlock the safe using the Master or User code, including signal indications.

Open the Safe

Instructions for opening the safe door after the lock has been disengaged.

Change Master Code

Procedure to change the primary 6-8 digit Master code, requiring current code entry.

Activate User Code 2

Steps to set up a secondary 6-8 digit User code, requiring Master code authentication.

Change User Code 2

Procedure to modify User Code 2 using the current Master code for authentication.

Delete User Code 2

Instructions to remove or disable the secondary User code using the Master code.

Battery Management

Battery Replacement

Guidance on replacing the 9 Volt battery when indicated by low-level warnings.

Emergency Power Use

How to use emergency power pins for access when the battery is completely discharged.

VALBERG BM 1993 Specifications

General

Brand	VALBERG
Model	BM 1993
Category	Safes
Language	English