'
>*+1&3*+&?.$53&.4&566A&.3&I.$$&30=+&'&
7.1#3+4&9+65,+&.3&-01&9+&$.3&0C0.1;
TO TURN ON APPLIANCE TO TURN OFF APPLIANCE
FLAME HEIGHT ADJUSTMENT
J& K1&3*+&/0$/+A&3#,1&LMN&=159&51&3*+&KNA&6#$$&
-5#13+,-$5-=I.4+&&&&&&&&&&&&&?54.3.51;
J& O$0-+&KNPKQQ&4I.3-*&G.6&+F#.??+2H&.1&<&GKN&
?54.3.51H;
STANDBY MODE (Pilot Flame)
J& O,+44&012&*5$2&&&&&&&G470$$&&07+H&35&4+3&0??$.01-+&03&
?.$53&&07+;
J& R.7#$301+5#4$%&?,+44&3*+&KQQ&012
&&&&&G$0,C+&&07+H&9#33514
.$&0&4*5,3&
9++?&-51&,74&3*+&430,3&4+F#+1-+&
*04&9+C#1S&,+$+04+&9#33514;
J& T513.1#.1C&9++?4&-51&,7&3*+&
.C1.3.51&.4&.1&?,5-+44;
J& K1-+&?.$53&.C1.3.51&.4&-51&,7+2A&
3*+,+&.4&70.1&C04&&5I;
J& M63+,&70.1&9#,1+,&.C1.3.51&3*+&
*0124+3&I.$$&0#35703.-0$$%&C5&.135&
701#0$&GLMNH&-513,5$&752+;
J& O,+44&KQQ&9#3351;
>*+1&3*+&?.$53&.4&566A&.3&I.$$&30=+&'&
7.1#3+4&9+65,+&.3&-01&9+&$.3&0C0.1;
J& <1&430129%&752+U&O,+44&012&*5$2
&&&&&G$0,C+&&07+H&9#3351&35&.1-,+04+&
&07+&*+.C*3;
WARNING
>*+1&?.$53&.C1.3.51&.4&-51&,7+2A&7535,&3#,14&
0#35703.-0$$%&35&70V.7#7&&07+&*+.C*3;
Remote Control Operation
NOTE: Before using the remote control system for
the fi rst time, 3*+&,+-+./+,&012&3*+&*0124+3&7#43&9+&
4%1-*,51.:+2;&R++&3*+&4+-3.51 Remote Control Initial
Set-up&51&3*+&?,+/.5#4&?0C+&56&3*.4&701#0$;&
Set (scrolls
through
modes and
settings)
OFF (returns
to set mode,
turns the burner
and the pilot o)
Large ame
button (ames
up, sets hours,
temperature)
Small ame
button (ames
down and o,
sets minutes,
temperature)
Current
temperature
(F or C)
Current time
(12 or 24 hour clock)
Modes (Manual,
Temperature, Timer)
Handset
sensor
Battery status
Current
programmed
period (Timer)
Period
start or end
(Temp, Timer)
Fan setting (if used)
Burner setting
W.4?$0%&K/+,/.+I
X0124+3&K/+,/.+I
N53+U&<1&3*+&)YLO&5,&)<LYD&752+4A&3*+&,+753+&
*0124+3&4+14+4&3*+&,557&3+7?+,03#,+&012&02@#434&3*+&
&07+&0--5,2.1C$%;&
)5&-577#1.-03+A&3*+&*0124+3&4*5#$2&9+&I.3*.1&!Z&6++3&
G[;Z&7+3+,4H&56&3*+&&,+?$0-+;&
Do not leave the handset on the mantel or hearth.
IMPORTANT:&BEFORE YOU BEGIN, please note that
on this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when
the function display is fl ashing. Be patient when
programming as it can take a few seconds to set.
To Next Page
Loading...
