To Next PageTo Next Page
Need help?Do you have a question about the Vaporesso Revenger and is the answer not in the manual?
Highlights key features like OMNI Board 2.0, IML Case, Slide-n-Fill, Mesh Drip Tip, and Heating Insulation.
Details technical specifications for the Revenger Kit, including tank size, mod dimensions, weight, and battery type.
Lists all items included in the Revenger Kit and Revenger Mod package for user convenience.
Instructions on turning the device on and off by pressing the fire button five times in quick succession.
Guide on how to inhale through the mouthpiece while holding the fire button to vape.
Explains the information shown on the OLED screen and the Real Time Clock function.
How the mod detects coils and automatically switches modes for specific coil types like Kanthal.
Instructions to lock and unlock adjustment buttons to prevent accidental changes during use.
How to rotate the screen display 180 degrees by pressing the up and down buttons simultaneously.
How to switch between different vaping modes like VW, VT, TCR, BYPASS, CCW, and CCT.
Information on charging the battery, displaying charge level, and the Remaining Charging Time.
How to update firmware and customize the device using software from the Vaporesso website.
How to adjust the bottom airflow system by slightly twisting the airflow ring.
Instructions for refilling the tank using the Slide-n-Fill design by sliding the top lip.
How to remove the base and insert new GT cores into the NRG Tank series atomizers.
Detailed explanations for Smart VW, CCW, and CCT modes, including adjustments and settings.
Instructions for TC-Ni, TC-Ti, TC-SS, and TCR modes, including TCR value ranges and temperature adjustments.
Explanation of Bypass mode's direct output and how to enable/disable Smart ON/OFF.
How to adjust screen timeout duration and reset the device to default settings.
Important warnings regarding usage by minors, handling, temperature, and battery disassembly.
Recommendations for using correct charging equipment, reputable batteries, and safe charging practices.
Lists precautions for device handling and outlines built-in protection functions like short circuit and over-temperature.
Information on nicotine addiction and potential side effects, advising consultation with a healthcare professional.
Highlights key features like OMNI Board 2.0, IML Case, Slide-n-Fill, Mesh Drip Tip, and Heating Insulation.
Details technical specifications for the Revenger Kit, including tank size, mod dimensions, weight, and battery type.
Lists all items included in the Revenger Kit and Revenger Mod package for user convenience.
Instructions on turning the device on and off by pressing the fire button five times in quick succession.
Guide on how to inhale through the mouthpiece while holding the fire button to vape.
Explains the information shown on the OLED screen and the Real Time Clock function.
How the mod detects coils and automatically switches modes for specific coil types like Kanthal.
Instructions to lock and unlock adjustment buttons to prevent accidental changes during use.
How to rotate the screen display 180 degrees by pressing the up and down buttons simultaneously.
How to switch between different vaping modes like VW, VT, TCR, BYPASS, CCW, and CCT.
Information on charging the battery, displaying charge level, and the Remaining Charging Time.
How to update firmware and customize the device using software from the Vaporesso website.
How to adjust the bottom airflow system by slightly twisting the airflow ring.
Instructions for refilling the tank using the Slide-n-Fill design by sliding the top lip.
How to remove the base and insert new GT cores into the NRG Tank series atomizers.
Detailed explanations for Smart VW, CCW, and CCT modes, including adjustments and settings.
Instructions for TC-Ni, TC-Ti, TC-SS, and TCR modes, including TCR value ranges and temperature adjustments.
Explanation of Bypass mode's direct output and how to enable/disable Smart ON/OFF.
How to adjust screen timeout duration and reset the device to default settings.
Important warnings regarding usage by minors, handling, temperature, and battery disassembly.
Recommendations for using correct charging equipment, reputable batteries, and safe charging practices.
Lists precautions for device handling and outlines built-in protection functions like short circuit and over-temperature.
Information on nicotine addiction and potential side effects, advising consultation with a healthcare professional.
The Vaporesso Revenger Kit is an advanced vaping device designed for an enhanced user experience, featuring the OMNI Board 2.0 chipset and a robust construction. It offers a wide range of functionalities and user-friendly features for both novice and experienced vapers.
The Revenger Kit is powered by two 18650 batteries (sold separately) and boasts a versatile output range of 5 to 220W. Its core is the OMNI Board 2.0 chipset, which enables multiple output modes, a quick charge system, and displays the remaining charging time. A notable innovation is the In-Mould Labeling (IML) case, providing superior wear resistance, enhanced graphic quality, and a refined texture.
The device is paired with the NRG Tank, a component designed for everyday vaping and cloud chasing. This tank incorporates innovative GT Cores, including traditional and signature CCELL Ceramic Coils, offering diverse vaping experiences. The Slide-n-Fill design simplifies e-liquid refills, making the process cleaner and more efficient. For user safety and comfort, the tank includes a heating insulation layer at the bottom and a mesh drip tip with a specially engineered structure to prevent spit back.
Ergonomically designed, the Revenger Mod features an all-metal fire button on the side for a comfortable grip. The industry-leading OLED screen provides comprehensive vaping information, including voltage, resistance, battery level, temperature, and output wattage. It also offers useful tips, such as the remaining time for a full battery charge, all managed by the OMNI Board 2.0.
The Revenger Kit offers various output modes, including Smart VW (H/N/S), CCW, CCT, VT (NI, TI, SS), TCR (M1, M2), RCT, and BYPASS, allowing users to customize their vaping experience. The temperature control range spans from 100°C-315°C / 200F-600F.
Switch On/Off: To power the device on or off, press the fire button five times in quick succession within two seconds.
Vaping: To vape, hold the fire button and inhale through the mouthpiece, then release the button.
Screen Display: Upon activation, the OLED screen displays essential information like voltage, resistance, battery level, temperature, and output wattage. If unused for 10 seconds, the display switches to a Real Time Clock, which then shuts off after 15 minutes of inactivity. Pressing any of the "+", "-", or Mode buttons will illuminate the screen with the Real Time Clock, and pressing them again will bring up the main menu. Pressing the fire button at any time will also light up the main menu.
Automatic Atomizer Recognition: The mod automatically reads the coil's resistance upon connection. If a Kanthal coil is detected, the mod will automatically switch from TC to wattage mode.
Adjustment Buttons Lock/Unlock: To lock the adjustment buttons, simultaneously press the Mode button and the "+" button for two seconds while the device is on; the screen will display "SYSTEM LOCKED." To unlock, press the "+" and Mode buttons simultaneously; the screen will display "SYSTEM UNLOCKED."
Switch Display Mode: To rotate the screen display 180 degrees, press the up and down buttons simultaneously for two seconds.
Switch Vaping Modes: Long-press the Mode button for three seconds to cycle through VW (H/N/S), VT (Ni200, SS, Ti), TCR, BYPASS, CCW, and CCT modes.
Charging: The device features a Quick Charge System and an equalizing charge system. Simply plug in the USB cable to charge. The OLED display shows the current battery level (0%, 20%, 50%, 80%, and 100%) and the remaining charging time, which updates every 10 minutes. The display remains lit during charging.
Firmware Update and Customizing: The device's firmware can be updated and customized via a simple software available for download from the Vaporesso website. The software runs on Windows systems, is in English, and includes a "help" section. Instructions for use are provided on the website and Facebook page.
Adjustment of Airflow: The bottom airflow system can be adjusted by slightly twisting the airflow ring.
Filling E-liquid: The Slide-n-Fill design allows for easy refilling. Slide the top lid counter-clockwise to its fullest extent, fill the e-liquid through the opening, and then slide the top back into place.
Changing Atomizer: To change the GT Cores, remove the base, unscrew the old GT Cores, insert the new GT Cores onto the base, and secure the base back in place. A variety of GT Cores are available for the NRG Tank series.
Smart VW Mode: This advanced Variable Wattage mode offers three levels: H (High), N (Normal), and S (Soft), with Normal as the default. It automatically selects the appropriate average wattage for your atomizer based on its resistance.
CCW Mode: In VW mode, press the mode button three times to select CCW. Hold the mode button to confirm and adjust the wattage line (ramp up time and performance) using the plus and minus buttons. Move to the next bar with a quick press of the mode button. Hold the mode button again to save and exit.
TC-Ni/TC-Ti/TC-SS/TCR (M1, M2) Mode: In TC-Ni/TC-Ti/TC-SS mode, the device supports Nickel 200, Titanium, and 316 Stainless Steel coils. The OMNI Board 2.0 allows adjustment of the start-up wattage in temperature control mode (default 65W). The coil value can also be adjusted within a given range. In TCR mode, the device supports different temperature control coils within various TCR value ranges, which can be set by the user.
Setting TCR Mode (M1, M2): In TC-Ni/TC-Ti/TC-SS mode, press the mode button three times to enter the TCR (M1, M2) set menu. Use the mode button to choose between M1 and M2. Use the up or down button to adjust the TCR value according to the coil material.
Adjust Temperature: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2) mode, temperature can be adjusted from 100-315°C or 200-600°F using the up or down buttons. Each press adjusts the temperature by 5°C or 10°F. Long-pressing the buttons allows for rapid adjustment.
Lock/Unlock Resistance: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2) mode, press the "-" and mode button simultaneously for two seconds to lock or unlock the resistance level. A "0" will appear on the display when locked. Attaching a new atomizer will not change the locked resistance.
Automatic Atomizer Recognition: For optimal temperature control, the mod will prompt the user if a new atomizer is attached with "OLD LOAD: -, NEW LOAD: +". Press "+" for a new atomizer to read its resistance, or "-" to read the locked resistance.
CCT Mode: In any TC mode, press the mode button three times to select CCT. Hold the mode button to confirm and adjust the temperature line using the plus and minus buttons. Move to the next bar with a quick press of the mode button. Hold the mode button again to save and exit.
Bypass Mode: This mode uses a direct output voltage system, where higher battery level results in higher output voltage. It supports coils with resistance in the range of 0.05-5ohm.
Smart ON/OFF: This advanced Variable Wattage mode can be switched on or off from the main menu without affecting VW (H/N/S). Enter Smart ON/OFF and confirm with Yes or No.
Screen Timeout: The default timeout is 10 seconds for the main menu, switching to Real Time Clock for another 15 minutes. The timeout can be adjusted from 3 to 60 seconds.
Default: The device can be reset to default settings by entering Default and pressing YES.
When inserting new batteries, ensure they are new and a matched pair. Unevenly charged, used, or non-matching batteries can cause significant charging delays and affect device performance.
The device includes several protection features:
General| Wattage Range | 5-220W |
|---|---|
| Display | 0.96" OLED |
| Dimensions | 89mm x 45mm x 28mm |
| Weight | Unknown |
| Voltage Range | 0-8.5V |
| Thread | 510 |
| Chipset | OMNI Board 2.0 |
| Battery Type | Dual 18650 (not included) |
| Resistance Range | 0.05-5.0 ohm |
| Temperature Range | 100°C - 315°C / 200°F - 600°F |
| Charging Current | 2.5A |
| Modes | Bypass |
| Charging | Micro USB |
| Tank Capacity | 5mL |
| Coil Compatibility | Vaporesso GT Cores |
