Need help?Do you have a question about the Varian 929-7015M002 and is the answer not in the manual?
General| Brand | Varian |
|---|---|
| Model | 929-7015M002 |
| Category | Controller |
| Language | English |
General overview of the E-Net Dual Controller, its features, and capabilities.
Explains how the controller distributes power between dual pumps, including priority and short-circuit handling.
Details electrical and environmental specifications for the controller unit.
Provides diagrams illustrating output voltage versus current and recorder output voltage.
Shows dimensional drawings of the E-Net Dual Controller's front and rear views.
Explains the location and replacement procedure for fuses in the controller.
Details the controller's connection points and cabling.
Describes the protective shutdown mechanism triggered by excessive current.
Explains how the controller adjusts voltage output based on current levels.
Provides the pinout and signal descriptions for the Remote I/O connector.
Lists the signals and their descriptions for the female Remote I/O connector outputs.
Lists the signals and their descriptions for the female Remote I/O connector inputs.
Describes the procedure for turning on the High Voltage via the Remote I/O connection.
Illustrates the timing sequence for High Voltage switch-on using interlocks.
Details the pinout for the RS232 serial connector.
General instructions for connecting and operating the E-Net Dual Controller.
Steps for powering up and initializing the controller.
Explains how to switch between LOCAL, SERIAL, and REMOTE I/O operating modes.
Shows examples of messages displayed for High Voltage channels and pump types.
Describes how to access and navigate the controller's configuration menu.
Explains messages displayed when navigating through the menu system.
Details how to select the desired unit of pressure measurement.
Explains how to select between High Voltage channels and Serial Communication.
Guides the user through selecting and configuring pump types.
Describes operations for reading parameters when a standard pump type is selected.
Explains how to display and change the maximum voltage (Vmax) setting.
Explains how to display and change the maximum current (Imax) setting.
Explains how to display and change the maximum power (Pmax) setting.
Explains how to display and change the protect current (Iprotect) setting.
Details how to set pressure readings for spare pumps.
Guides on setting pressure set-points for all pump models.
General information about the controller's serial interface.
Specifies the serial data transmission format and timing parameters.
Explains how to select the serial communication baud rate.
Lists possible data exchange errors and their causes during serial communication.
Outlines the data fields and modes for the controller's software protocol.
Details the command and reply formats for binary serial communication.
Lists and describes general commands for controlling the E-Net Dual Controller.
Provides ASCII and Hex codes for general usage commands.
Details the command coding for controlling High Voltage on/off.
Lists device numbers and types for specific pump configurations.
Explains the bitfield coding for interlock status.
Lists commands and possible values for High Voltage operations.
Lists commands and possible values for High Voltage operations.
Details the command coding for Remote I/O inputs and outputs.
Lists commands used for configuring controller parameters.
Lists ASCII and Hex codes for general usage commands.
Explains the bitfield coding for serial property settings.
Lists and describes error codes for protocol communication issues.
Categorizes and describes various error types and their references.
Introduces Ethernet communication via MOXA card and TCP/IP framework.
Guides on configuring the IP address for Ethernet communication.
Shows how to perform a broadcast search for MOXA cards on the network.
Demonstrates changing the IP address of the MOXA card.
Shows configuration options for the MOXA card, including network and console settings.
Details how to modify IP address and Netmask settings for the MOXA card.
Explains the confirmation process for modified card settings and browser connection.
Guides on configuring RS232 serial settings on the MOXA card.
Details how to configure the MOXA card for TCP server mode functionality.
Describes how to define operating parameters for the MOXA card.
Lists available accessories and their part numbers.
Fields for customer contact and billing details.
Section for product details like description, part number, and serial number.
Options for specifying the type of product return.
Certification regarding hazardous materials exposure.
Lists common failure modes for turbo pumps and turbocontrollers.
Lists common failure modes for ion pumps and controllers.
Lists common failure modes for valves and components.
Lists common failure modes for leak detectors.
Lists common failure modes for instruments.
Lists common failure modes for primary pumps.
Lists common failure modes for diffusion pumps.
Space to provide a detailed description of the malfunction.
To Next Page
