Need help?Do you have a question about the VeEX VePAL TX300 and is the answer not in the manual?
Details single and dual port Ethernet configuration options and test modes.
Describes Fibre Channel port operation modes, including pass-through monitoring.
Lists supported OTN/SDH/SONET interface types and impedance.
Safety precautions for optical connectors and laser sources.
Safety precautions for electrical connectors and potential voltage hazards.
Provides an overview of the test set's physical layout and components.
Details the functions of each key on the device's keypad.
Information on operating the LCD touch screen display and precautions.
Details about the unit's rechargeable Li-ion battery pack.
Description of physical test ports and interfaces.
Explains the functions of fixed and soft LEDs on the unit.
Instructions for updating the test set software via USB or ReVeal MTX300.
Describes the three presentation areas of the Home Menu screen.
Explains the meaning of various status icons displayed on the screen.
Outlines the available test modes for the TX300/e.
Describes the navigation path to access the Setup menu.
Describes setting up interfaces and test parameters for the Signal tab.
Details the setup procedures for PDH signals.
Details the setup procedures for SDH signals.
Details the setup procedures for SONET signals.
Details the setup procedures for OTN/SDH signals.
Details the setup procedures for OTN/SONET signals.
Configures measurement settings including timer, performance analysis, and general options.
Displays PDH test results including summary, errors, alarms, event log, signal, histogram, graph, and performance analysis.
Displays SDH test results including summary, errors, alarms, event log, signal, histogram, graph, and performance analysis.
Displays SONET test results including summary, errors, alarms, event log, signal, histogram, graph, and performance analysis.
Displays OTN test results including summary, errors, alarms, event log, and signal.
Describes generating different anomalies into the transmit signal.
Lists the PDH and T-Carrier alarms and errors that can be generated.
Lists the SDH alarms and errors that can be generated.
Lists the OTN alarms and errors that can be generated.
Explains how to inject errors during testing.
Lists the shortcuts for accessing OTN Tools.
Analyzes and generates overhead information.
Analyzes the OTN frame structure.
Analyzes the OTU overhead.
Analyzes the ODU overhead.
Analyzes the OPU overhead.
Sets the Payload Structure Identifier (PSI) for payload configuration.
Manages path trace testing and screens.
Analyzes or edits Tandem Connection Monitoring (TCM) bytes.
Provides access to SDH/SONET testing tools.
Lists shortcuts for SDH/SONET Tools.
Displays Section/Line and Path Overhead bytes.
Edits Section/Line and Path Overhead bytes.
Displays and generates AU/TU pointer values and movements.
Generates and edits J0, J1, J2 path traces.
Sets C2 and V5 Path Signal Labels for High order/STS and Low order VCs.
Measures Automatic Protection Switching limits.
Analyzes or edits Tandem Connection Monitoring (TCM) bytes.
Scans tributaries to check signal structure, trace ID, and payload.
Measures propagation time through the network.
Provides information on Jitter and Wander measurements.
Monitors channel health and rate of individual tributaries.
Captures and analyzes E1 pulse shape for conformance testing.
Captures and analyzes E3 pulse shape for conformance testing.
Measures Automatic Protection Switching limits for E1 links.
Explains the NFAS word for E1 signal framing.
Measures round trip delay for PDH signals.
Displays received data and captures current timeslots for E1.
Covers ISDN PRI call setup, signal, trace, multi-call, DTMF, dbackup, and monitor modes.
Performs talk/listen functions for VF channels.
Provides information on Jitter and Wander measurements.
Captures and analyzes DS1 pulse shape for conformance testing.
Accesses DS1 loopback features.
Measures round trip delay for DS1/3 signals.
Displays received data and captures timeslots for DS1.
Captures and analyzes DS3 pulse shape for conformance testing.
Configures Far End Alarm and Control Channel Responses for DS3.
References E1 ISDN PRI instructions.
Performs talk/listen functions for VF channels.
Provides information on Jitter and Wander measurements.
Emulates CSU or NIU for DS1 service verification.
Measures and analyzes received signal jitter.
Defines sinusoidal jitter amplitude causing designated errors.
Defines output jitter to input jitter ratio versus frequency.
Measures long-term phase variations of a digital signal.
Software for viewing and analyzing TIE data results.
Overview of Overclocked OTN testing capabilities.
Compensates for rate mismatch with 10GbE LAN and OPU2 payload.
Enables Ethernet options like BERT, RFC 2544, Throughput.
Selects the test interface or mode.
Configures Transmitter and Receiver interfaces and test parameters.
Configures interface parameters like test port and clock source.
Configures test patterns for OTN mapping.
Configures measurement settings.
Configures audible alarm and measurement clock source.
Provides a summary of OTN test results and parameters.
Details errors and alarm status for OTN signals.
Displays a chronological log of error and alarm events.
Displays signal level and frequency measurements.
Configures test mode, ports, and network settings for Ethernet tests.
Performs Bit Error Rate Testing.
Tests network link performance using throughput, latency, frame loss, and burst.
Automated Ethernet service activation test feature.
Tests throughput performance for multiple traffic streams.
Provides defect detection, fault management, and performance monitoring.
Enables bi-directional monitoring of traffic.
Establishes manual loopback on the test set.
Accesses additional test applications like Scan.
Overview of Fibre Channel applications and network types.
Highlights key test applications in Fibre Channel.
Configures test interfaces, applications, and port settings.
Performs BERT and Throughput tests for Fiber Channel.
Tests Fiber Channel circuits for RFC 2544 compliance.
Accesses the loopback function on the Fiber Channel Home menu.
Defines Layer 1 and Layer 2 specifications for CPRI.
Focuses on verifying BER requirements for CPRI Transport links.
Configures BERT settings for CPRI testing.
Displays CPRI BERT test results including summary, signal, errors, alarms, and events.
Explains how to create, save, and load test configuration profiles.
Provides IP configuration and testing tools.
Network Wizard for network configuration.
WiFi Wizard for wireless network configuration.
Accesses advanced test applications.
Provides access to common utilities.
Manages saved files and test results.
Information on using the ReVeal software.
Controls the display backlight settings.
Details the warranty period for hardware, software, and accessories.
Warrants hardware products against defects in materials and workmanship.
Warrants software and firmware materials against defects.
States warranty limitations and exclusions.
Lists conditions under which the warranty may be revoked.
Explains the CE marking requirements.
Explains the Restriction of Hazardous Substances (RoHS) compliance.
General| Platform | VePAL |
|---|---|
| Model | TX300 |
| Category | Test Equipment |
| Ethernet Testing | Yes |
| OTN Testing | Yes |
| SDH/SONET Testing | Yes |
| PDH/DSn Testing | Yes |
| Fibre Channel Testing | Yes |
| Battery Life | Up to 8 hours |
| Form Factor | Portable |
| Test Type | Multi-Service Transport Test |
| Protocols Supported | Ethernet, OTN, SDH/SONET, PDH/DSn, Fibre Channel |
| Power Supply | AC/DC |
| Display | Touchscreen |
| Operating Temperature | -10°C to +50°C |
| Storage Temperature | -20 to 70 °C |
| Humidity | 5% to 90% non-condensing |
To Next Page
