Firmware Version ???
AIR WEIGHER
M
M350S Quick Setup Guide - two channel
1 2
print menutare
gross
1 2
print menuzero
net
Conguration
Calibration
System
M
E
N
U
ok
Display
Diagnostics
Alarms
Options
SPLIT SCREEN
Shows channel 1 front axle group
and channel 2 rear axle group
MENU
MENU
with options activated
MENU
selectable options
NET
total load in body note, zero will appear
+/- 500 kg to mute alarm press any key
GROSS
total truck weight note, zero will appear
+/- 500 kg
menu
n
e
t
Channel 1
kg
n
e
t
Channel 2
kg
kg
kg
Display Changes OLED contrast to high, medium
or low. Also shows info: version & serial no.
Diagnostics Engineers screen. Shows two channel
weights and input milli-volt signals
Alarms Two alarm setpoints - PIN code required
To mute Alarm - press any key
Options Modes: Switches GROSS on & off
Load: On or off
RS232: Printer or scoreboard mode
Count by: 1, 10, 20, 50, 100, & 200 kgs
Z/Func: Allow/inhibit keyboard zero
Configuration To select 1 or 2 channels, air, oil or
fifth wheel.
Split: For split axle systems. Option for
total Ch1 + Ch2 or seperate Ch1 & Ch2
calibrations
Calibration Weighing system calibration settings
System Accesses password set and resets.
Note. for PUK (PIN unlock code) contact
service who will take you through your
PIN retrieval. Edit time and date in system
Alarm graphic - shows both alarms.
Alarm set key
Print key - prints net, gross, time & date in weighing screens
Menu key - scrolls thru’ NET, GROSS & MENU screens
Service reminder, flashes when weigher service is due
OK key - enters data
Down arrow key - scrolls down menu
Up arrow key - scrolls up menu
Back Up key - goes back a step
A
F
E
B
C
D
G
I
H
Note
GROSS or GVW (gross vehicle weight) is the total truck weight (NET + TARE)
NET ‘net load’ means the payload weight in the truck body
LOAD means part load collected or delivered, press PRINT to print and zero the load, weight
collected is stored as an accumulation to NET
SPAN where used, means the NET weight used to calibrate the weigher
TARE weight means the weight of the empty vehicle
ALARM where fitted, an alarm sounder or flashing beacon will activate when alarm setpoint is reached
ON SITE when ‘load’ is turned on in options, on site allows logging onto site and
off site for weighing loads collected from a site with multiple bins (waste only)
TWIN means two channels are displayed and calibrated separately
DUAL means the indictor will split the weight readings between the channels
B
C
D
E
A
Power-up the display by either switching on the ignition (ignition live
wiring) or press the power button beneath the logo (where tted) if
the indicator is permanently wired to the vehicle supply.
to switch ON turn ignition
and/or press logo
Vehicle Weighing Solutions
Version 4D-01-16
Serial No:12B57664
For Service Tel: 0161 643 0202
M350S
Welcome screen
appears for 10 seconds
Service and calibration due screen
appears for 5 seconds
Service due Jan 2010
Press key to scroll up and
down menu screens
menu
M
E
N
U
Conguration
Calibration
System
ok
Display
Diagnostics
Alarms
Options
F
G
H I
MENU screen
info@vwsltd.co.uk
www.vwsltd.co.uk
need help? call service
0161 643 0202
31 March 2011 by MSB
Vehicle Weighing Solutions
Unit 4a Sheepbridge Business Centre
Sheepbridge Lane, CHESTERFIELD S41 9RX
Tel: 01246 455 946
Fax: 01246 769 665
INSTALLATIONS
Vehicle Weighing Solutions
Unit 5, Southview Park, Marsack Street,
Caversham, READING RG4 5AF
T: 0118 946 1900
F: 0118 946 1862
SALES
SERVICE
Vehicle Weighing Solutions (North)
United Business Centres Ltd.
4 Howarth Court, Gateway Crescent
Oldham Broadway Business Park
Oldham OL9 9XB
Tel. 0161 669 6193
To Next Page
Need help?
General