Velleman DVM1500 - Voltage Measurements; Resistance Measurements

16.04.2010
• Set the
• Place th
mains o
an AC v
o
Note: thi
s
and doe
DC-volt
a
Voltage
D
o
>
Al
w
3
0
ti
m
th
e
• Connec
t
to the "
C
• Set the
measur
e
• Press th
• Connec
t
• The me
a
Note: for
red test
Resista
n
D
o
• Connec
t
to the "
C
• Set the
• Press th
• Connec
t
• The me
a
• Notes:
o Neve
r
sure
a
o To in
c
the ti
p
value
of th
e
o For r
e
secon
o Shoul
of an
rotary switch to t
h
e top of the multi
-
utlet. The green L
o
ltage is present.
s
function is only a
s not guarantee t
h
a
ges. When in do
u
measuremen
t
o
not measure c
i
1000V CAT II
m
w
ays be careful w
h
0
Vac rms. Keep yo
m
es during measu
e
meter is linked
t
t
the red test lead
C
OM" jack.
rotary switch to
V
e
ments.
e RANGE button t
o
t
the test probes t
o
a
sured value appe
DC-measurement
s
lead, the indicate
n
ce measure
m
o
not perform re
t
the red test lead
C
OM" jack.
rotary switch to "
Ω
e RANGE button t
o
t
the test probes t
o
a
sured value appe
r
perform resistan
c
a
ll capacitors are
c
c
rease accuracy w
p
s of the measuri
n
of the test leads.
e
circuit.
e
sistance measure
ds to stabilize the
d the measured r
e
open circuit, the
d
DVM1500
9
h
e EF- range. T
h
-
meter as close a
s
ED will turn red a
n
n indication whet
h
h
at a circuit is vol
t
u
bt, perform a full
t
s
i
rcuits where vo
l
m
ay reside.
h
en working with
v
ur fingers behind
rement. Do not to
t
o a circuit which i
to the "V °C
V
for DC measu
r
o
manually select
o
the source bein
g
ars on the LCD di
s
s
, when a negativ
e
d value is preced
e
m
ents
sistance measu
r
to the "V °C
Ω
”
o
manually select
o
the source bein
g
ars on the LCD di
s
c
e measurements
c
ompletely deplet
e
hen measuring lo
w
n
g probes togethe
Subtract this val
u
ments above 1M

read-out.
e
sistance exceed
t
d
isplay will show “
©
h
e green LED will
s
s
possible to the le
n
d the multi-mete
h
er an AC voltage
t
age-free. It does
voltage measure
m
l
tages > 600V C
A
v
oltages above 6
0
the probe barrier
s
uch unused termi
n
s bein
g
tested.
Hz" jack and the
b
r
ements or to V
the range.
g
measured.
s
play.
e
polarity is prese
e
d by a “-” sign.
r
ements on live
c
Hz" jack and the
b
the range.
g
measured.
s
play.
on a live circuit a
n
e
d.
w
resistance value
r to determine th
e
u
e from the meas
u

the meter needs
t
he current range
o
OL”.
Rev. 01
©
Velleman nv
s
witch on.
ad or the
r will beep
is present,
not detect
m
ent.
A
T III or
0
Vdc or
s
at all
n
als when
b
lack lead
for AC
nt at the
c
ircuits.
b
lack lead
n
d make
s, first hold
e
resistance
u
red value
a few
o
r in case