EasyManua.ls Logo

Ventura 60 - User Manual

Default Icon
2 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Required material for VENTURA 60 litres
Ÿ M10 attachment set, article no. 1143-00
Ÿ Drilling machine with drill bit ø 10mm
Ÿ Spirit level
Ÿ Socket wrench, SW 17
Figure 2: Bore pattern
Set fixed anchors (see Figure 3). Remove the upper nut along with washer.
Place the container at the desired location and mark out the bore pattern. Alternatively, the bore pattern can be marked out as per Figure 2.
VENTURA 60: Drill ø 10mm holes to a depth of approx. 70mm.
VENTURA 110: Drill ø 12mm holes to a depth of approx. 90mm.
Adjust the lower nut to 25-30mm (the nuts must first be adjusted to the highest point on uneven ground).
Then level out the remaining nuts using the spirit level based on the first nut.
Put the container into position and screw it into place.
Insert the interior container and fix using the securing rod.
Figure 3: Cross-section of attachment
ø10 x 70 / ø12 x 90
25-30 *
45-55 *
* the stated size is only valid at the highest point on uneven ground
Required material for VENTURA 110 litres
Ÿ M12 attachment set, article no. 1145-00
Ÿ Drilling machine with drill bit ø 12mm
Ÿ Spirit level
Ÿ Socket wrench, SW 19
Figure 1: Remove the interior container
Open container, remove securing rod and interior container (Figure 1).
2
3
4
5
6
7
robi-ag.com
ROBI AG Kohlackerstrasse 17 CH-4323 Wallbach +41 (0)61 865 10 10 +41 (0)61 865 10 19
Base assembly for VENTURA 60 / 110 waste bin
15789.2018.01.E.INT
ø10
292
170
(35)
VENTURA 60
240*
(275)
(415)
360*
ø12
380
220
(40)
VENTURA 110
300*
(350)
(500)
460*
* concrete foundation
Question and Answer IconNeed help?

Do you have a question about the Ventura 60 and is the answer not in the manual?

Summary

Base Assembly for VENTURA Waste Bins

Required Material for VENTURA 60 Litres

List of required materials for the base assembly of the VENTURA 60 litre waste bin.

Required Material for VENTURA 110 Litres

List of required materials for the base assembly of the VENTURA 110 litre waste bin.

Step 1: Prepare Container

Open the container, remove the securing rod and interior container.

Step 2: Position and Mark

Place the container at the desired location and mark out the bore pattern.

Step 3: Drill Anchor Holes

Drill holes for anchors based on the VENTURA model size (Ø 10mm for 60L, Ø 12mm for 110L).

Step 4: Set Fixed Anchors

Install fixed anchors, removing the upper nut and washer.

Step 5: Adjust and Level Nuts

Adjust lower nuts to 25-30mm and level remaining nuts using a spirit level.

Step 6: Position and Screw Container

Put the container into position and screw it into place.

Step 7: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Post Mounting for VENTURA Waste Bins

Required Material for VENTURA 60 Litres (Post Mount)

Materials needed: strapping system and Allen key for post mounting VENTURA 60.

Required Material for VENTURA 110 Litres (Post Mount)

Materials needed: strapping system and Allen key for post mounting VENTURA 110.

Post Mount Step 1: Prepare Container

Open container, remove securing rod and interior container.

Post Mount Step 2: Loosen Pipe Mounting

Loosen the pipe mounting component.

Post Mount Step 3: Set Pipe Mounting Height

Set the pipe mounting on the rod or candelabra to the desired height.

Post Mount Step 4: Mount Container

Mount the container and screw it into place.

Post Mount Step 5: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Wall Mounting for VENTURA Waste Bins

Required Material for VENTURA 60 Litres (Wall Mount)

Materials: M8 attachment set, drill, spirit level, socket wrench for wall mounting VENTURA 60.

Required Material for VENTURA 110 Litres (Wall Mount)

Materials: M10 attachment set, drill, spirit level, socket wrench for wall mounting VENTURA 110.

Wall Mount Step 1: Prepare Container

Open container, remove securing rod and interior container.

Wall Mount Step 2: Mark Bore Pattern

Mark out the bore pattern in accordance with the diagram.

Wall Mount Step 3: Drill Anchor Holes

Drill Ø 8mm holes for VENTURA 60 and Ø 10mm for VENTURA 110.

Wall Mount Step 4: Set Fixed Anchors

Set fixed anchors into the drilled holes.

Wall Mount Step 5: Position and Screw Container

Put the container into position and screw it into place.

Wall Mount Step 6: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Summary

Base Assembly for VENTURA Waste Bins

Required Material for VENTURA 60 Litres

List of required materials for the base assembly of the VENTURA 60 litre waste bin.

Required Material for VENTURA 110 Litres

List of required materials for the base assembly of the VENTURA 110 litre waste bin.

Step 1: Prepare Container

Open the container, remove the securing rod and interior container.

Step 2: Position and Mark

Place the container at the desired location and mark out the bore pattern.

Step 3: Drill Anchor Holes

Drill holes for anchors based on the VENTURA model size (Ø 10mm for 60L, Ø 12mm for 110L).

Step 4: Set Fixed Anchors

Install fixed anchors, removing the upper nut and washer.

Step 5: Adjust and Level Nuts

Adjust lower nuts to 25-30mm and level remaining nuts using a spirit level.

Step 6: Position and Screw Container

Put the container into position and screw it into place.

Step 7: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Post Mounting for VENTURA Waste Bins

Required Material for VENTURA 60 Litres (Post Mount)

Materials needed: strapping system and Allen key for post mounting VENTURA 60.

Required Material for VENTURA 110 Litres (Post Mount)

Materials needed: strapping system and Allen key for post mounting VENTURA 110.

Post Mount Step 1: Prepare Container

Open container, remove securing rod and interior container.

Post Mount Step 2: Loosen Pipe Mounting

Loosen the pipe mounting component.

Post Mount Step 3: Set Pipe Mounting Height

Set the pipe mounting on the rod or candelabra to the desired height.

Post Mount Step 4: Mount Container

Mount the container and screw it into place.

Post Mount Step 5: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Wall Mounting for VENTURA Waste Bins

Required Material for VENTURA 60 Litres (Wall Mount)

Materials: M8 attachment set, drill, spirit level, socket wrench for wall mounting VENTURA 60.

Required Material for VENTURA 110 Litres (Wall Mount)

Materials: M10 attachment set, drill, spirit level, socket wrench for wall mounting VENTURA 110.

Wall Mount Step 1: Prepare Container

Open container, remove securing rod and interior container.

Wall Mount Step 2: Mark Bore Pattern

Mark out the bore pattern in accordance with the diagram.

Wall Mount Step 3: Drill Anchor Holes

Drill Ø 8mm holes for VENTURA 60 and Ø 10mm for VENTURA 110.

Wall Mount Step 4: Set Fixed Anchors

Set fixed anchors into the drilled holes.

Wall Mount Step 5: Position and Screw Container

Put the container into position and screw it into place.

Wall Mount Step 6: Insert Interior Container

Insert the interior container and fix it using the securing rod.

Overview

  1. Function Description
  2. Important Technical Specifications
  3. Usage Features
  4. Maintenance Features

This document provides instructions for the assembly and mounting of the VENTURA 60 and VENTURA 110 waste bins, detailing both base assembly and two types of mounting: post mounting and wall mounting. The instructions cover the necessary materials, step-by-step procedures, and relevant technical specifications for each method.

Function Description

The VENTURA 60 and VENTURA 110 are waste bins designed for various installation methods, including base assembly (freestanding), post mounting, and wall mounting. The primary function is to provide a secure and stable receptacle for waste, with features for easy installation and maintenance. The design incorporates an interior container that can be removed for emptying and a securing rod to hold it in place. Different models cater to varying capacities (60 litres and 110 litres) and corresponding mounting requirements.

Important Technical Specifications

General:

  • Models: VENTURA 60 (60 litres) and VENTURA 110 (110 litres).
  • Securing Mechanism: Interior container secured by a rod.

Base Assembly (Freestanding):

  • VENTURA 60:
    • Attachment Set: M10, article no. 1143-00.
    • Drill Bit: Ø 10mm.
    • Drilling Depth: Approx. 70mm.
    • Socket Wrench: SW 17.
    • Bore Pattern Dimensions:
      • Overall width: 415mm.
      • Overall depth: 350mm.
      • Hole spacing (width): 360mm.
      • Hole spacing (depth): 292mm.
      • Distance from edge to hole (width): 27.5mm.
      • Distance from edge to hole (depth): 29mm.
    • Anchor Type: Fixed anchors.
    • Anchor Projection: 25-30mm above ground (adjustable for uneven ground).
    • Concrete Foundation: Required for stability.
  • VENTURA 110:
    • Attachment Set: M12, article no. 1145-00.
    • Drill Bit: Ø 12mm.
    • Drilling Depth: Approx. 90mm.
    • Socket Wrench: SW 19.
    • Bore Pattern Dimensions:
      • Overall width: 500mm.
      • Overall depth: 380mm.
      • Hole spacing (width): 460mm.
      • Hole spacing (depth): 380mm.
      • Distance from edge to hole (width): 20mm.
      • Distance from edge to hole (depth): 0mm.
    • Anchor Type: Fixed anchors.
    • Anchor Projection: 25-30mm above ground (adjustable for uneven ground).
    • Concrete Foundation: Required for stability.

Post Mounting:

  • VENTURA 60:
    • Strapping System: E.g., «Bandimex».
    • Allen Key: 6mm.
  • VENTURA 110:
    • Strapping System: E.g., «Bandimex».
    • Allen Key: 8mm.
  • Mounting Type: Pipe mounting on a rod or candelabra.
  • Adjustability: Pipe mounting allows for height adjustment.

Wall Mounting:

  • VENTURA 60:
    • Attachment Set: M8, article no. 1144-00.
    • Drill Bit: Ø 8mm.
    • Drilling Depth: Approx. 70mm.
    • Socket Wrench: SW 13.
    • Bore Pattern Dimensions (Figure 1):
      • Overall height: 750mm.
      • Overall width: 80mm.
      • Hole spacing (vertical): 885mm (center to center).
      • Hole diameter: Ø8mm.
      • Distance from edge to hole (horizontal): 77mm.
    • Anchor Type: Fixed anchors.
    • Anchor Projection: 25-30mm above ground (adjustable for uneven ground).
  • VENTURA 110:
    • Attachment Set: M10, article no. 1143-00.
    • Drill Bit: Ø 10mm.
    • Drilling Depth: Approx. 90mm.
    • Socket Wrench: SW 17.
    • Bore Pattern Dimensions (Figure 1):
      • Overall height: 750mm.
      • Overall width: 80mm.
      • Hole spacing (vertical): 885mm (center to center).
      • Hole diameter: Ø10mm.
      • Distance from edge to hole (horizontal): 77mm.
    • Anchor Type: Fixed anchors.
    • Anchor Projection: 25-30mm above ground (adjustable for uneven ground).

Tools required for all installations:

  • Spirit level.
  • Drilling machine.

Usage Features

The VENTURA waste bins are designed for straightforward installation and user-friendly operation.

  • Versatile Mounting Options: The ability to choose between freestanding (base assembly), post mounting, and wall mounting allows for flexible placement in various environments, adapting to specific spatial and aesthetic requirements.
  • Easy Container Access: The design facilitates easy removal of the interior container, simplifying waste collection and disposal.
  • Secure Installation: The use of fixed anchors and specific attachment sets ensures a stable and secure installation, preventing accidental tipping or displacement.
  • Leveling Capability: For base assembly and wall mounting, the adjustable lower nuts on the fixed anchors allow for precise leveling of the bin, even on uneven ground, ensuring stability and a neat appearance.
  • Height Adjustment (Post Mounting): The pipe mounting system enables adjustment of the bin's height on a rod or candelabra, catering to different user heights or environmental considerations.

Maintenance Features

Maintenance of the VENTURA waste bins is designed to be simple and efficient.

  • Easy Interior Container Removal: The interior container can be easily removed by opening the main container and detaching the securing rod. This allows for quick emptying and cleaning of the container.
  • Accessible Components: The design ensures that all components, including the securing rod and interior container, are easily accessible for inspection, cleaning, or replacement if necessary.
  • Durable Materials: While not explicitly stated, the requirement for specific attachment sets and drilling depths suggests a robust construction intended for long-term use in various conditions.
  • Simple Reassembly: After maintenance or emptying, the interior container can be quickly reinserted and secured with the rod, making the bin ready for use again with minimal effort.
  • Standardized Fasteners: The use of standard socket wrenches (SW 13, SW 17, SW 19) and Allen keys (6mm, 8mm) for installation and adjustments means that common tools can be used for any necessary maintenance or re-tightening.

Ventura 60 Specifications

General IconGeneral
BrandVentura
Model60
CategoryGarbage Disposal
LanguageEnglish