Vermeer D60x90 Navigator

Questions and Answers

K
kristen21Aug 14, 2025
What to do if Vermeer D60x90 Navigator has low battery output?
- A
  Ashley LeonardAug 15, 2025
  If your Vermeer Drill has low battery output, several factors could be responsible. It may be due to a low water level (add water), a loose alternator belt (tighten the belt), or a defective alternator (replace the alternator). Other possible causes include corroded or loose battery cables (clean and tighten battery cables), a defective battery cell (replace the battery), a cracked battery case or broken terminal (replace the battery), or a dirty or wet battery top causing discharge (clean the battery top).
J
Joseph DiazAug 18, 2025
What to do if Vermeer D60x90 Navigator has low battery charge?
- A
  amanda24Aug 18, 2025
  If your Vermeer Drill has a low battery charge, it could be due to several reasons. The alternator may not be charging (see your Vermeer dealer), or there may be corroded or loose battery cables (clean and tighten battery cables). Other potential causes include poor wiring connections in the battery charging circuit (check wiring connections), a defective battery cell (replace battery), a faulty regulator (replace regulator), excessive engine idling (reduce engine idle), or a continuous drain on the battery due to a dirty battery top or shorted electrical components (clean battery top).
M
Miranda TrujilloAug 21, 2025
Why Vermeer Drill has no hydraulic power?
- P
  Penny WallsAug 21, 2025
  If your Vermeer Drill has no hydraulic power, there are several potential causes. The operator may not be in the seat when using drill functions (sit in the operator’s seat), or there may be no hydraulic fluid (fill with fluid). It's also possible that the battery voltage is too low to shift the solenoid (check battery, alternator and charging circuit), the Remote Lockout system may be activated (place Remote Lockout system in RUN mode), there may be damaged or worn hydraulic pump or a damaged relief valve (see your Vermeer dealer).
A
amanda36Aug 25, 2025
What to do if Vermeer Drill has hydraulic power loss?
- C
  charles53Aug 25, 2025
  If your Vermeer Drill is experiencing hydraulic power loss, several issues could be the cause. Check for low hydraulic fluid (add hydraulic fluid), a plugged hydraulic filter (replace filter), or a plugged hydraulic strainer (clean strainer). Other possible causes include the wrong viscosity of hydraulic oil (change hydraulic fluid to correct viscosity), a worn pump or motor, or an improper pressure relief setting (see your Vermeer dealer).
C
carloscoxAug 27, 2025
Why Vermeer D60x90 Navigator Drill battery uses too much water?
- C
  Connie MartinAug 27, 2025
  If the battery in your Vermeer Drill is using too much water, it could be due to a cracked battery case (replace battery) or an overcharged battery (see your Vermeer dealer).
M
Mary AdamsAug 31, 2025
What to do if Vermeer Drill has slow hydraulic power?
- M
  Martha ThompsonAug 31, 2025
  If your Vermeer Drill exhibits slow hydraulic power, several factors could be responsible. Begin by checking the hydraulic fluid level (add hydraulic fluid) and inspecting the hydraulic filter (replace filter) and strainer (clean strainer) for any blockages. Other potential causes include a worn pump, improper pressure relief setting (see your Vermeer dealer), or cold hydraulic fluid (warm up machine and operate hydraulic system).
S
Shelby BrooksSep 3, 2025
What to do if Vermeer D60x90 Navigator Drill Remote Lockout system not responding?
- B
  bhernandezSep 3, 2025
  If the Remote Lockout system on your Vermeer Drill is not responding, several factors could be the cause. Ensure the operator is in the seat when the system is turned on (sit in seat and select RUN or LOCKOUT mode). Cold weather operation can increase hydraulic oil viscosity, preventing pressure switches from confirming lockout (move throttle to its lowest setting). Lockout may not be confirmed due to the machine being in Transport mode (change from Transport mode to Drill mode). Other potential causes include being out of range (move into range) or a low battery (replace battery).
S
Shannon CantrellSep 6, 2025
Why is the hydraulic pump noisy in Vermeer D60x90 Navigator Drill?
- S
  Stacy MooreSep 6, 2025
  A noisy hydraulic pump in your Vermeer Drill could be due to cold hydraulic fluid. To address this, warm up the machine at reduced engine speed.
T
Tina MartinSep 10, 2025
Why Vermeer Drill oil foams?
- C
  colliernicoleSep 10, 2025
  If the oil in your Vermeer Drill is foaming, it could be due to low hydraulic fluid (add hydraulic fluid), water in the hydraulic fluid (change fluid), or an air leak between the tank and pump (repair leak).