VEVOR XRJF-11 - User Manual

Questions and Answers

E
Eric LongAug 18, 2025
How to troubleshoot no display on VEVOR XRJF-11 after power on?
- H
  Haley WillisAug 18, 2025
  If there is no display after you power on your VEVOR Beverage Dispenser, check the power supply, plugs, and sockets to ensure they are properly connected and energized. If the issue persists, the internal wires may have been damaged; in this case, hire a professional electrician to replace or fix them. If these steps don't resolve the problem, the computer board may have failed, and you should contact the company's professional staff for assistance.
S
Shirley RossAug 20, 2025
Why does the power switch trip on my VEVOR XRJF-11 Beverage Dispenser?
- L
  lmillerAug 20, 2025
  If the power switch trips after turning on your VEVOR Beverage Dispenser, it could be due to several reasons. First, the input power line or switch load may be insufficient, requiring a professional electrician for replacement. Second, internal circuits might be damaged, also needing professional repair. Third, the gear setting may be too high, causing excessive load; try adjusting it downward. Lastly, a short circuit in the motor, circuit board, or compressor could be the cause, and you should contact the company's professional staff for assistance.
R
Robin KnoxAug 23, 2025
What causes abnormal noise in my VEVOR Beverage Dispenser after powering it on?
- P
  Patrick MontgomeryAug 23, 2025
  Abnormal noise from your VEVOR Beverage Dispenser can stem from several sources. If the noise occurs when pressing the cleaning key, it should diminish after adding raw materials. Ensure the machine is on a level surface; if not, adjust it. Cooling noises should also reduce with added material. High gear settings can cause noise, so adjust accordingly. Check the fan for obstructions or loose screws. For compressor noise, ensure the condenser is clean. If these steps don't address the noise, further internal checks may be needed.
T
Timothy HoweAug 26, 2025
Why are smoothie discharges from my VEVOR XRJF-11 too soft or too little?
- L
  Laura CobbAug 26, 2025
  If your VEVOR Beverage Dispenser is producing smoothies that are too soft or insufficient in quantity, consider these factors: avoid discharging too frequently; wait until the molding ratio reaches at least 90% before mixing the material. Ensure proper heat dissipation by providing at least one meter of space on both sides of the machine for ventilation. Adjust the gear settings if they are insufficient. Finally, a failure in the machine's cooling system, such as refrigerant leakage or compressor failure, could be the cause.
P
pricematthewAug 27, 2025
What to do if VEVOR XRJF-11 makes no smoothie or smoothie is too soft after stopping?
- L
  Luke RodriguezAug 27, 2025
  If your VEVOR Beverage Dispenser is not producing smoothies or they are too soft after stopping the machine, several factors could be responsible. Ensure the beating handle is correctly positioned. Note that the first cup may be softer after a long shutdown, which is normal. Adjust gear settings and downtime appropriately. A failure in the discharge micro switch or sensing anomalies could also be the cause; consider replacing the switch or checking the motor magnets and speed sensor.
L
Lori ScottAug 30, 2025
Why can't my VEVOR XRJF-11 reach "99"?
- M
  Michael MendozaAug 30, 2025
  If your VEVOR Beverage Dispenser is unable to reach "99", consider these potential causes: improper gear selection (adjust downward), poor cooling (check for a dirty or blocked condenser and ensure smooth exhaust air flow), high ring temperature (ensure good ventilation), unstable voltage or insufficient power supply (consult a professional), or refrigeration evaporation cylinder issues (leakage of slush).
B
bautistaryanSep 1, 2025
Why am I feeling leakage after powering on my VEVOR XRJF-11 Beverage Dispenser?
- J
  Jason MayoSep 1, 2025
  If you feel a leakage after powering on your VEVOR Beverage Dispenser, the machine case may have inductive electricity. Check if the power inlet line is reliably grounded and that there is a grounding wire. If the wire is worn, replace it.
T
Thomas SloanSep 3, 2025
Why is my VEVOR XRJF-11 leaking water and material from the discharge head?
- E
  ethansimpsonSep 3, 2025
  If you notice water or material leaking on or under the discharge head of your VEVOR Beverage Dispenser after starting it, check the following: Ensure the two D-rings of the outlet valve are correctly installed in the slot. Inspect the O-ring of the beating rod for wear and replace if necessary. Tighten the four screws diagonally and evenly. When disassembling the beating rod, pull it out vertically and lubricate the valve stem seal with medical petroleum jelly during installation. Also, ensure the discharge head screws are tightened.
A
Amber LiSep 5, 2025
What does machine 55 alarm mean on a VEVOR XRJF-11 Beverage Dispenser?
- A
  Anthony MorganSep 6, 2025
  If your VEVOR Beverage Dispenser displays a "55" alarm, it could indicate several issues. The tank might be freezing, requiring a downward gear adjustment. Alternatively, the motor may not be rotating or its idling speed is slow, or there could be a sensor failure or loose sensor linkage. In these cases, it's recommended to contact the company's professional staff for assistance. Also, check if the motor is damaged, which could cause a slow motor speed.
M
Michael MoonSep 8, 2025
How do I fix a "UH" alarm on my VEVOR Beverage Dispenser?
- A
  Aaron WardSep 8, 2025
  To address the "UH" alarm on your VEVOR Beverage Dispenser, adjust the voltage or add a 6KW regulator.

Summary

Safety Instructions

Electrical Requirements

Details essential power supply and grounding guidelines for safe operation.

Usage

Outlines safe operating practices, prohibitions, and precautions for machine use and maintenance.

Usage Environment

Specifies ideal placement conditions, temperature limits, and environmental considerations for optimal machine performance and safety.

Installation Instructions for The Whole Machine

Installation of Slushy Machine

Provides guidelines on machine placement, ventilation, spacing, and handling during installation.

Installation of the Power Supply

Details requirements for connecting the machine to a suitable and grounded power outlet.

Names of Each Part

Pre-boot Inspection

Lists crucial checks to perform before powering on the slushy machine.

Proper Operation When Using

Details essential do's and don'ts for safe and effective machine operation.

Product Specifications

Operating Instructions

Password Input Interface

Explains how to access the parameter setting interface using a specific password.

Parameter Setting Interface

Details how to adjust settings like slush gear, cycle time, and temperatures.

Out-of-Material Alarm Function

Explains how the level float system detects low material levels and triggers an alarm.

Slush Production

Raw Material Preparation

Guides on diluting concentrates with water and achieving the correct sugar percentage.

Raw Material Filling

Instructions on preparing the freezing tank and filling it with slush raw material.

Start The Machine

Refers to operating instructions and warns against inserting fingers into the feed bowl.

Make Smoothies

Explains that the machine stops at 99% shape ratio, ready for dispensing.

Simple Cleaning

Cleaning & Maintenance

Cleaning Method of Parts

Instructions for cleaning disassembled parts using food detergent and brushes.

User Considerations

Warnings about handling parts, avoiding hot water, and soaking times.

Cleaning And Maintenance of The Enclosure

Cleaning of The Condenser

Schedule and method for cleaning the condenser for optimal heat dissipation.

Consumable Parts

Information on frequently replaced parts like sealing rings and their replacement frequency.

The Assembly Method of The Component

Methods for Installing on The Machine

Safety precautions regarding power switches and hand disinfection during assembly.

Mounting of The Handle

Instructions for attaching the handle to the lever pin and holder.

Installation of Agitators

Procedure for inserting and rotating agitators into the freezer tank.

Installation of Discharge Manifolds

Steps for attaching discharge valves to the heads using bolts.

Troubleshooting Instructions

Circuit Diagram

Environmental List

VEVOR XRJF-11 Specifications

General

Model	XRJF-11
Category	Beverage Dispenser
Brand	VEVOR
Material	Stainless Steel
Number of Tanks	1
Power Supply	110V/60Hz
Cooling Method	Compressor
Number of Taps	1
Insulation	Polyurethane Foam
Wheels	No
Capacity	12L
Net Weight	20kg

Related product manuals

VEVOR X-150

8 pages