Victron energy Pylontech US3000C User Manual

2022-10-02 11:47 1/11
Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UP5000, Phantom-S, Force-
L1 & L2
Victron Energy - https://www.victronenergy.com/live/
Victron & Pylontech US2000, US3000 and
Phantom-S
The combination of Victron products with Pylontech lithium batteries has been tested and certified by
the Victron and Pylontech R&D departments.
General information about the battery is found in Pylontech's documentation.
This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It
provides additional and specific information regarding integration with Victron systems.
The Pylontech includes a Battery Management System (BMS) with each battery module. This
interfaces with the Victron GX device and can support multiple battery modules connected in parallel.
1. Product & system compatibility
Battery US2000 (Plus) US3000 Force-L1
Module capacity 2.4 kWh 3.5 kWh 3.55 kWh
1.1 Offgrid, Backup and Energy Storage Systems are possible
Victron + Pylontech can be used for the following system types:
Off-grid
Grid Backup
Energy Storage Systems - Self Consumption (ESS - Start page)
1.2 A GX-device is required, eg Color Control GX (CCGX) or Venus GX (VGX)
It is essential to use the CAN-bus connection of the GX device (eg CCGX or VGX) with the batteries for
the keep-alive signal, communication of charge and discharge limits, error codes and state of charge.
The minimum required firmware version for the Color Control GX is v2.15. It is highly recommended to

Victron energy Pylontech US3000C Specifications

General

Battery Type	Lithium Iron Phosphate (LiFePO4)
Nominal Voltage	48 V
Max Continuous Charge Current	74 A
Max Continuous Discharge Current	74 A
Depth of Discharge (DoD)	90%
Warranty	10 years
Scalability	Up to 16 units in parallel
Weight	32 kg
Protection Class	IP20
Nominal Capacity	3552 Wh
Usable Capacity	3200 Wh
Charge Voltage	53.5V
Cycle Life	6000 cycles
Communication	CAN, RS485
Operating Temperature Range	-10°C to 50°C
Storage Temperature Range	-20°C to 60°C
Dimensions (H x W x D)	442 x 420 x 132 mm
Communication Interface	CAN, RS485

Summary

Victron Pylontech Product and System Compatibility

Supported System Types for Pylontech Batteries

Describes system types like off-grid, grid backup, and Energy Storage Systems (ESS).

GX Device Requirement for Pylontech Integration

Explains the necessity of a GX device for battery communication and control.

Compatible Victron Inverter/Charger Models and Firmware

Lists compatible Victron inverter/charger models and required firmware versions.

Compatible Victron MPPT Chargers and Connections

Details compatibility with Victron VE.direct MPPT chargers and connection requirements.

Minimum Battery Sizing Recommendations

Pylontech CAN-bus Wiring Guide

VEConfigure Settings for Pylontech Battery Integration

General Tab Settings in VEConfigure

Explains settings for the General tab in VEConfigure for Pylontech batteries.

Charge Settings Configuration in VEConfigure

Details the specific charge settings for Pylontech batteries in VEConfigure.

Inverter Settings for Pylontech Operation

Covers inverter settings within VEConfigure for optimal Pylontech battery operation.

ESS System Settings for Pylontech Batteries

Describes ESS-specific settings for Pylontech batteries in VEConfigure.

GX Device Settings for Pylontech Battery Management

VE-Direct MPPT Settings for Pylontech

Victron Pylontech Example System Wiring Diagram

Troubleshooting Victron Pylontech Systems

Victron Pylontech FAQ and Known Issues

Further Information and Resources