6 | 90501 DE___Benutzerhandbuch |
5 Assembly instrucons
See image 4
A Shower Head Fing B Shower Head
C On/O D Gasket
E Inlet port
5.1 Assembling the shower
1. Please assemble the shower head as displayed in the
diagram.
2. Locate the 'shower head ng' and wrap it 5 to 7 mes
with the Teon tape provided.
3. Select the shorter end of the extension pipe and wrap it 3
to 5 mes with Teon tape. Then thread shower head onto
taped end of pipe unl snug. DO NOT OVERTIGHTEN.[4-1]
4. Tightly wrap the threads on the remaining end of the
extension pipe with Teon tape 8 to 10 mes. Carefully
thread the wrapped end of the extension pipe into the
coupler of the shower unl snug. DO NOT OVERTIGHTEN.
5 If the 'shower head' is poinng up, simply rotate unl it is
poinng down.
5. Follow steps 1 and 2 for the 'Foot Shower'.[4-2]
6. Tightly wrap the 'Foot Shower' threads 5 to 7 mes with the
Teon tape provided. Carefully thread the 'Foot Shower'
into the couple of the shower unl snug. DO NOT
OVERTIGHTEN.
7. Aach a garden hose to connect the 'Inlet Port' of the
shower to a water supply.[4-4]
5 In case of leaks at either coupler during step 1 or 2,
remove shower head from ng and wrap threading 3 to 4
more mes with Teon tape before reaaching.[4-1]
8. Match the hot and cold water handle with the quadrate
part of the blue faucet. Install the screw to x the handle.
Put the red and blue cover on the hole of the handle. Please
pay aenon to ensure the red part is on the le and blue
is on the right.
5.2 Mounng the shower
concrete/masonry installaon only
1. Choose a locaon for the shower that receives the most
direct sunlight.
2. Use the main unit to mark the posion of the mounng
holes to be drilled into concrete/masonry for bolts.[4-3]
3. Remove shower. Drill ½ " (13mm) diameter holes, 1 ¾ "
(44mm) deep, using the marks just created.
4. Insert expansion nuts into holes. Place the bolt inside the
expansion nut and tap with a hammer to slightly expand
the nut.
5. Remove bolt and place the base plate/lower tube over the
holes and secure it to the surface with bolts and washers
provided.
5 Base plate will appear loose unl shower is fully secured
to the surface.
6 Installaon instrucons
1. Drill holes in the concrete oor or other solid ground and
bolt the solar shower onto the ground. Make sure the solar
shower will withstand strong winds and other external
forces.
2. It is advisable to install the solar shower in places with a lot
of sunshine.
3. The quick connect adaptor is used for the water inlet. We
suggest using exible hoses. Make sure the exible hose
can withstand pressure of 6 kg/cm
2
.
4. Test for leaks aer installaon. Parts may have come loose
during installaon, causing leaking. Therefore, locang and
ghtening such parts may help resolve the leaks.
DE Benutzerhandbuch
1 Allgemeine Warnhinweise
Lesen Sie alle Anweisungen und Warnungen sorgfälg durch,
bevor Sie dieses Produkt in Betrieb nehmen. Die Nichtbeachtung
von Warnungen und Anweisungen kann zu schweren
Verletzungen, Tod oder Sachschäden führen. Überprüfen Sie
vor der Installaon, ob alle Zubehörteile vollständig vorhanden
und unbeschädigt sind. Falls das nicht der Fall sein sollte,
wenden Sie sich bie an unseren Kundendienst. Bewahren Sie
diese Anleitung zum späteren Nachschlagen an einem sicheren
Ort auf. Verwenden Sie dieses Produkt nur mit
Originalzubehörteilen. vidaXL haet nicht für Beschädigungen
bzw. Verletzungen, die infolge unsachgemäßen Gebrauchs
dieses Produkts entstehen. Die in dieser Gebrauchsanweisung
enthaltenen Informaonen werden zum Zeitpunkt der
Drucklegung nach bestem Wissen und Gewissen als korrekt
erachtet. vidaXL behält sich jedoch das Recht vor, Änderungen
oder Ergänzungen der Vorgaben ohne vorherige Ankündigung
vorzunehmen. Reparaturen dürfen nur von einem Fachmann
oder einem erfahrenen Heimwerker durchgeführt werden.
Versuchen Sie niemals, das Produkt selbst zu reparieren.
2 Einleitung
Eigenschaen
• Das Duschrohr besteht aus Umwelt-PVC, das keine giigen