Videx 4800 - User Manual

66250070-EN - V1.5 - 11/12/14
1
4000 Series
Art.4800 - 4800M - Installation instructions
Art.4800 - 4800M Digital codelock module
CODELOCK UNIT MODULES ART.4800  4800M
The module features 12 stainless steel buttons (Keys 0 - 9,
ENTER and CLEAR), 2 LED’s for progress information during
use and programming and a mirror nish stainless steel front
plate (Standard version). With three integral relays each with
common, normally open and normally closed connections and
two inputs to enable the external triggering of relays one and
two (For example, push to exit button). Key presses are signalled
both acoustically and visually while each button press has a tac-
tile feel. Entering the correct code followed by ENTER will ac-
tivate the relevant relay. Programming is carried out through
the same keypad following a simple programming menu. The
module can be combined with other 4000 Series modules in an
audio or video intercom system.
‘
MAIN FEATURES
• 3 C, NC, NO relay outputs (24Vac/dc – 5A max);
• 3 Programmable secret codes (one for each relay);
• Each relay can be set to be activated for a specic time (01 to 99 seconds) or to work as latch;
• Two active low inputs to command directly the relay 1 and 2;
• Programming menu guarded by a 4-8 digit programmable engineer’s code;
• Visual and Acoustic signal during operating and programming;
• Keypad illumination LEDs;
GENERAL DIRECTIONS FOR INSTALLATION
In order to achieve the best results from the schematics described it is necessary to install only original VIDEX equipment, strictly
keeping to the items indicated on each schematic and follow these General Directions for Installation:
• The system must be installed according to national rules in force, in any case the running of cables of any intercom unit must be
carried out separately from the mains;
• All multipair cables should be compliant to CW1308 specication (0.5mm twisted pair telephone cable).
• Cables for speech line and service should have a max resistance of 10 Ohm
• Lock release wires should be doubled up (Lock release wires and power supply wires should have a max resistance of 3 Ohm);
• The cable sizes above can be used for distances up to 50m. On distances above 50m the cable sizes should be increased to keep
the overall resistance of the cable below the RESISTANCES indicated above;
• Double check the connections before power up;
• Power up the system then check all functions.
LOCK RELEASE BACK EMF PROTECTION
A varistor must be  tted across the terminals on AC lock release
(Fig.1A)
and a diode must be  tted across the terminals on a DC
lock release
(Fig.1B) to suppress back EMF voltages. Connect the components to the lock releases as shown in  gures.
VARISTOR (MOV)
12V AC
LOCK RELEASE
Fig.1A
DIODE
1N4002
12V DC
LOCK RELEASE
Fig.1B
Fig. 1 - Art.4800 - 4800M

Summary

Codelock Module Overview

Main Features

Key features include relay outputs, secret codes, and inputs.

Installation Guidelines

Guidelines for proper installation, cable types, and connections.

Lock Release EMF Protection

Protection methods for lock releases using varistors and diodes.

Module Operation and Programming

Buzzer Back EMF

Capacitor requirement for intercom buzzer call.

Built-in Relay EMF Protection

Selectable back EMF protection for relays using jumpers.

Programming Procedures

Steps for entering engineer's code and setting up relays.

Operation Modes and Notes

How to use the codelock, error handling, and relay control.

Technical Specs and Programming Flowchart

Technical Specification

Power supply, consumption, and operating temperature details.

Programming Flowchart

Visual guide illustrating the programming sequence.

Contact and Support Information

Videx Office Contacts

Lists contact details for various international offices.

Customer Support

Provides technical support contact information for customers.

Videx 4800 Specifications

General

Operating Voltage	12Vdc
Buttons	12
Backlight	Yes
Voltage	12V DC
Material	Metal