What to do if Villa Sistemi Medicali Medical Equipment displays messages related to HF board problems?
If you see messages about HF board issues on your Villa Sistemi Medicali Medical Equipment, switch the unit off and wait a few seconds to allow the circuit capacitors to discharge. Then, switch the unit back on. If the problem continues, it is necessary to call the Technical Service.
General| Voltage Range | 40 - 150 kV |
|---|---|
| Focal Spot Size | 0.6 / 1.2 mm |
| X-ray Tube | Rotating Anode |
| Digital Detector Type | Flat Panel Detector |
| Exposure Time Range | 1 ms - 10 s |
| Image Receptor | Digital Detector |
Details critical warnings related to device operation, environment, and maintenance.
Emphasizes safety during installation and service, especially regarding high voltage.
Explains the service programs accessible via passwords for unit configuration and testing.
Details specific passwords for configuring the unit's hardware settings.
Lists the safety standards and directives the STRATO 2000 Digital complies with.
Details procedures for measuring technical factors like kV and mA.
Warns about high voltage present when accessing internal parts for measurements.
Explains the non-invasive method for verifying exposure parameters.
Details electrical supply requirements, connection procedures, and safety devices.
Details the procedure for checking and adjusting the panoramic alignment using lasers.
Guides the user through the cephalometric alignment check using a PC and software.
Details annual inspection activities performed by authorized technical personnel.
Covers necessary verifications and adjustments for centering the device's components.
Describes the procedure for aligning the axes for panoramic examinations.
Details centering the rotation, X, and Y axes using laser alignment.
Explains how to center the X-ray beam for panoramic imaging after laser alignment.
Outlines the procedure for aligning axes for cephalometric examinations.
Details the alignment of the rotation arm for cephalometric functions.
Describes how to set the ear centering circles for cephalometric alignment.
Guides the centering of the secondary collimator for cephalometric mode.
Explains the procedure for centering the cephalometric sensor.
Details the adjustment procedure for the Soft Tissue Filter in cephalometric mode.
Details the steps for aligning the rotation arm using lasers and software.
Explains how to set the ear centering circles using specific software and tests.
Guides the centering of the secondary collimator using software and X-rays.
Details the centering process for the cephalometric sensor using software.
Explains how to adjust the Soft Tissue Filter using software and X-ray exposure.
Describes the procedure to measure kV and exposure time using invasive methods.
Provides detailed steps for measuring kVp using a multimeter and test points.
Explains how to verify exposure time accuracy using an oscilloscope.
Details the invasive method for measuring mA values on the HF generator board.
Explains the different types of messages displayed by the unit for operational and error conditions.
Lists error codes related to motor movements and their corresponding reference chapters.
Lists error codes for the primary collimator and their reference chapters.
Lists error codes for the soft tissue filter and their reference chapters.
Lists error codes related to the secondary collimator and their reference chapters.
Lists error codes for the CEPH sensor and their reference chapters.
Lists error codes related to the HF board and tubehead, with reference chapters.
Lists error codes related to button functionality and their reference chapters.
Lists error codes for memory checksum issues and their reference chapters.
Provides an overview of service programs, their levels, and access methods.
Describes how to use Password 94 for testing various system components.
Explains how to test the CPU board's input signals and microswitch status.
Details how to test the functionality of the keyboard keys and indicator lights.
Explains how to diagnose and resolve error E560 related to button presses during startup.
Details troubleshooting for error E561 when the X-ray button is released during emission.
Explains how to diagnose and resolve error E562 related to X-ray button presses during startup or prep.
Details troubleshooting for error E563 concerning the remote X-ray button.
Describes a test to verify CPU and HF board connectivity and piloting signals.
Guides troubleshooting for error E550 indicating no voltage supply to the HF board.
Details troubleshooting for error E551 related to overvoltage on the HF board.
Explains troubleshooting for error E552 indicating an overload condition.
Details troubleshooting for error E553 when a fault is detected in the X-ray tube filament circuit.
Guides troubleshooting for error E554 when the system does not sense X-ray ON signal.
Details troubleshooting for error E555 indicating an unwanted X-ray emission.
Describes how to use Password 118 to calibrate motors, sensors, and axes.
Details the procedure for zeroing and calibrating the X-axis motor (M5).
To Next Page
