villavent 251-16 User Manual

122656 23.01.01/AT/KMB
Montasje-, bruks- og vedlikeholdsanvisning, kjøkkenhette, type 251-16
Installation, user and maintenance instructions, cookerhood, type 251-16
Bruk, Fig. 1
A Bryter for viftemotor/spjeld
B Bryter for lys
1,2,3 Hastighetsvelger for vifte, 3
trinn for komfyravtrekk
4 Grunnventilasjon
5 Forsert ventilasjon
6 Lampe lyser ved forsert
ventilasjon
Flambering under hetten må ikke
forekomme. Sørg for tilstrekkelig
lufttilførsel til rom der kjøkkenhette er
installert.
Vedlikehold
Kjøkkenhetten rengjøres med varmt
såpevann og klut. Rengjør filteret ca.
2 ganger pr. måned. Filteret tas ut
som vist i fig. 2. Bløtlegg filterduken
og filterristen i varmt vann tilsatt
oppvaskmiddel. Eventuelt kan hele
filterkassetten vaskes i opp-
vaskmaskin før den settes tilbake i
hetten.
NB! Manglende rengjøring kan
føre til oppsamling av fett
og dermed brannfare.
Skifte av lysrør
For utskifting av lysrør åpnes
lampedekselet som vist i fig. 3.
(Sokkel G23).
Feilsøking
Test lysrør og om hetten fungerer på
alle hastigheter. Kontakt din
leverandør eller Villavent as,
tlf.: + 47 51969700
Operation, Fig. 1
A Switch for fan speed/damper
B Switch for light
1,2,3 Fan speed control, 3 steps
with open damper
4 Minimum ventilation
5 Forced ventilation
6 Light on indicates forced
ventilation
Flaming under the cookerhood must
not occur. Ensure sufficient fresh air
supply to room where cookerhood is
installed.
Maintenance
Remove filter for cleaning at least
twice a month, fig. 2. Soak the filter
cloth and grill in warm soapy water.
At the same time wipe the inside of
the cookerhood. The filter casette
can alternatively be washed in dish
washer. Let filter dry properly before
replacing.
Note!Build-up of grease and dust
inside the cookerhood
increases the risk of fire.
Changing the light bulb
For changing of light bulb, open the
lamp cover as shown in fig. 3 (socket
G23).
Troubleshooting
Test light bulb and that the
cookerhood is operating on all fan
speeds. Contact your local supplier
for further assistance.

villavent 251-16 Specifications

General

Brand	villavent
Model	251-16
Category	Ventilation Hood
Language	English

Summary

Operation and Controls

Fan Speed and Ventilation Settings

Controls fan speed (3 steps) and ventilation modes (min, forced).

Light Control

Switch to control the cookerhood light.

Ventilation Indicator

Light indicates when forced ventilation is active.

Maintenance and Safety

Routine Cleaning

Clean hood with warm soapy water; wipe inside.

Filter Maintenance

Soak filter cloth/grill in warm soapy water; dishwasher safe.

Fire Risk Warning

Buildup of grease/dust increases fire risk. Clean regularly.

Bulb and Troubleshooting

Light Bulb Replacement

Open lamp cover as shown in Fig. 3 to change bulb.

Troubleshooting Steps

Test bulb/fan; contact supplier for persistent issues.

Technical Specifications

Dimensions and Electrical Data

Details width, electrical connection, and light bulb specifications.

Power and Voltage

Max power consumption and transformer output voltages.

Installation Guide

Ducting Requirements

Exhaust duct must be cleanable, non-flammable, and separate from smoke ducts.

General Installation

Follow extract fan instructions and local regulations.

Damper Installation

Install damper axle 'A' ensuring clips 'B' secure the top plate.

Cookerhood Mounting

Mount under cupboard; maintain distance from hob; use brackets if needed.

Electrical Installation

Must be performed by an authorized installer.

Airflow Adjustment

Basic Ventilation Setting

Adjust sliding damper 'A' to desired position using marking 'B'.

Pressure Drop Measurement

Mount hose on measuring outlet 'C' on the damper for measurement.

Transformer Voltage Change

Remove covers, loosen screws, and pull plate forward to access transformer.

Ventilation Performance

Static Pressure vs. Airflow

Graph showing static pressure drop for different damper settings and airflow.

Forced Ventilation Performance

Graph shows airflow and sound levels for forced ventilation.

Sound Level Definitions

Defines LpA (sound pressure) and LwA (sound power) levels.