Need help?Do you have a question about the Vitrifrigo MACS and is the answer not in the manual?
Provides manufacturer details and contact information.
Details the components included in the MACS Vitrifrigo kits.
Guidance on where and how to position the air conditioner unit.
Instructions on how to securely mount the air conditioner unit.
Steps for setting up the condensate drain system.
Details the type and diameter of pipes for the sea water circuit.
Information on rotating the unit's fan for air outlet positioning.
Details on the placement and function of the return air grille.
Guidance on positioning the supply grille for optimal air distribution.
Instructions for installing air ducts and their recommended diameters.
Steps for assembling the electrical panel and its components.
How to install the air conditioner's control panel on the wall.
Instructions for connecting the sea water pump to the electronic board.
Guidelines for connecting the unit to the boat's power supply.
Steps for starting the system in cooling mode.
Steps for starting the system in heating mode.
How to turn the air conditioner system on and off.
Instructions for adjusting the desired temperature.
How to select between cooling, heating, auto, or ventilation modes.
Options for setting manual or automatic ventilation modes.
How to set the automatic timer for switching the machine on or off.
How to change the language displayed on the control panel.
Adjusting the brightness of the control panel display.
Configuring the audible signals (buzzer) for different events.
Setting the display to show temperature in Celsius or Fahrenheit.
Displays the temperature measured by the primary temperature probe.
Displays the temperature from an optional secondary probe.
Allows setting the minimum selectable temperature value.
Allows setting the maximum selectable temperature value.
Setting the temperature difference that triggers compressor operation.
Calibrating the temperature probe for accuracy.
Defines the off-time duration for the compressor between cycles.
Adjusts the minimum fan speed in heating mode.
Auto fan speed adjustment based on temperature difference.
Allows changing the system's access password.
Resets all parameters to their factory default values.
Sets the lowest fan speed selectable in heating mode.
Overview of functions available via the infrared remote control.
Configures the delay time before a general alarm is reported.
Sets a delay for when alarm messages are shown on the display.
Controls whether probe error alarms are enabled or disabled.
Controls whether pressure switch alarms are enabled or disabled.
Sets an error reporting delay for pressure switch alarms.
Enables or disables thermal alarms for compressor protection.
Sets a delay for reporting thermal alarm errors.
Explains how malfunction messages are displayed.
Maintenance for the return air grille and filter.
Maintenance checks for supply and return air grilles.
Cleaning and checking the condensate drain system.
Importance of cleaning the sea water strainer to prevent issues.
Notes on priming and maintenance of the sea water pump.
Checking hydraulic connections for leaks and proper flow.
Maintenance and checks for electrical connections and components.
Information on the factory-charged refrigerant level.
Steps to prepare the system for winter storage.
Procedure for draining and preparing the system when the boat is out of water.
Troubleshooting steps when the unit fails to operate.
Diagnosing why the fan runs but the compressor does not start.
Troubleshooting when the compressor runs but the fan does not.
Identifying causes and solutions for poor cooling performance.
Troubleshooting poor heating performance.
Diagnosing and resolving noise issues with the AC unit.
Troubleshooting and fixing water leaks from the unit.
Addressing safety concerns related to electrical shock.
Provides manufacturer details and contact information.
Details the components included in the MACS Vitrifrigo kits.
Guidance on where and how to position the air conditioner unit.
Instructions on how to securely mount the air conditioner unit.
Steps for setting up the condensate drain system.
Details the type and diameter of pipes for the sea water circuit.
Information on rotating the unit's fan for air outlet positioning.
Details on the placement and function of the return air grille.
Guidance on positioning the supply grille for optimal air distribution.
Instructions for installing air ducts and their recommended diameters.
Steps for assembling the electrical panel and its components.
How to install the air conditioner's control panel on the wall.
Instructions for connecting the sea water pump to the electronic board.
Guidelines for connecting the unit to the boat's power supply.
Steps for starting the system in cooling mode.
Steps for starting the system in heating mode.
How to turn the air conditioner system on and off.
Instructions for adjusting the desired temperature.
How to select between cooling, heating, auto, or ventilation modes.
Options for setting manual or automatic ventilation modes.
How to set the automatic timer for switching the machine on or off.
How to change the language displayed on the control panel.
Adjusting the brightness of the control panel display.
Configuring the audible signals (buzzer) for different events.
Setting the display to show temperature in Celsius or Fahrenheit.
Displays the temperature measured by the primary temperature probe.
Displays the temperature from an optional secondary probe.
Allows setting the minimum selectable temperature value.
Allows setting the maximum selectable temperature value.
Setting the temperature difference that triggers compressor operation.
Calibrating the temperature probe for accuracy.
Defines the off-time duration for the compressor between cycles.
Adjusts the minimum fan speed in heating mode.
Auto fan speed adjustment based on temperature difference.
Allows changing the system's access password.
Resets all parameters to their factory default values.
Sets the lowest fan speed selectable in heating mode.
Overview of functions available via the infrared remote control.
Configures the delay time before a general alarm is reported.
Sets a delay for when alarm messages are shown on the display.
Controls whether probe error alarms are enabled or disabled.
Controls whether pressure switch alarms are enabled or disabled.
Sets an error reporting delay for pressure switch alarms.
Enables or disables thermal alarms for compressor protection.
Sets a delay for reporting thermal alarm errors.
Explains how malfunction messages are displayed.
Maintenance for the return air grille and filter.
Maintenance checks for supply and return air grilles.
Cleaning and checking the condensate drain system.
Importance of cleaning the sea water strainer to prevent issues.
Notes on priming and maintenance of the sea water pump.
Checking hydraulic connections for leaks and proper flow.
Maintenance and checks for electrical connections and components.
Information on the factory-charged refrigerant level.
Steps to prepare the system for winter storage.
Procedure for draining and preparing the system when the boat is out of water.
Troubleshooting steps when the unit fails to operate.
Diagnosing why the fan runs but the compressor does not start.
Troubleshooting when the compressor runs but the fan does not.
Identifying causes and solutions for poor cooling performance.
Troubleshooting poor heating performance.
Diagnosing and resolving noise issues with the AC unit.
Troubleshooting and fixing water leaks from the unit.
Addressing safety concerns related to electrical shock.
General| Brand | Vitrifrigo |
|---|---|
| Model | MACS |
| Category | Chiller |
| Language | English |
To Next Page