Vivanco UR S2 - User Manual

UR S2 UNIVERSAL TV- DVB CONTROLLER
Vivanco GmbH, D-22926 Ahrensburg, E-Mail : hotline@vivanco.de ,
1
(GB) Instructions  1
(D) Bedienungsanleitung  3
(F) Notice d’emploi  5
(E) Instrucciones para el uso  7
(I) Istruzioni per l’uso  9
(NL) Gebruiksaanwijzing  11
(PL) Instrukcja obsługi  13
(CZ) Návod k obsluze  15
(P) Manual de instruções  17
(N) Bruksanvisning  19
(DK) Betjeningsvejledning  21
(S) Bruksanvisning  22
(FIN) Käyttöohje  24
(RUS) Руководство по эксплуатации  26
(GR) Οδηγίες χρήσης  28
(SK) Návod na obsluhu  31
Vivanco Addresses  33
(GB) Instructions
VIVANCO UR S2 Remote Control
Inserting the batteries
Open the battery flap on the back of
the remote control, press the tongue
lightly downwards, then insert 2
alkaline AA batteries. Check that the
polarity markings on the batteries and
in the battery compartment are
correctly lined up (+=+), then close the
flap carefully. – Always use
undamaged batteries.
Adapting to appliances
In order to control e.g. your TV or DVB
you must adapt or set the remote
control to it. There are two ways of
doing so: direct control code entry or
code search.
Direct control code entry using the
enclosed list
Example: setting to control a
Panasonic television set:
1. The attached list gives, for
example, the Panasonic Code 176.
Please make sure you have selected
the correct list for television sets (TV).
2. To prepare code entry,
press the SET button, keep it pressed
and then press the required appliance
button, e.g. TV, additionally until the
lamp (LED) lights constantly.
3. Then press the number
buttons (e.g. 1 7 6) in sequence.
4. Once the numbers have
been entered the lamp goes out and
the remote control is ready to control
your appliance.
5. Finally, test the control
code setting by trying to control (in this
example) your television set. If it does
not work at all or not correctly try a
different code from the list or the code
search (see below).
You can terminate the mode by
pressing any device button.

Summary

Vivanco UR S2 Universal TV-DVB Controller Instructions

Inserting the batteries

Open battery flap, insert 2 AA batteries checking polarity. Close flap. Always use undamaged batteries.

Adapting to appliances

To control your TV or DVB, adapt the remote. Two ways: direct code entry or code search.

Code Search Methods

Manual Code Search

Switch on appliance, press SET + appliance button until LED lights. Press SET, then repeatedly press ON/OFF to find code.

Automatic Code Search

Switch on appliance. Press DVB/appliance button, then SET for 5s until LED blinks. Remote emits signals. Press SET to end.

Code Identification

Read off 3-digit codes by pressing appliance button + SET + 1, 2, or 3. Count LED blinks for each digit.

Handling and Technical Data

Appliance Operation

Operate like original remote; press device button first. Test all buttons to identify functions as symbols may differ.

Volume-Function Punch-Through

When codes are set for satellite/DVB-T, UR S2 automatically uses TV volume and mute functions.

Technical Data

Power: 2x AA batteries. Range: max 7m. Not for 400 kHz devices. 2 years manufacturer warranty.

Vivanco Addresses

Austria

Vivanco Austria GmbH contact details for sales and support.

Germany

Vivanco GmbH contact details for sales and support.

United Kingdom

Vivanco (UK) Ltd. contact details for consumer support.

Vivanco UR S2 Specifications

General

Brand	Vivanco
Model	UR S2
Category	Universal Remote
Language	English