Vivotek IB9367-EHT-v2 - Page 245

VIVOTEK
User's Manual - 245
© 2020 VIVOTEK INC. All Right Reserved
105
NAME VALUE SECURITY
(get/set)
DESCRIPTION
_saturation
<Not
recommended to
use this>
saturation
100: Use "
image_c<0~(n-1)>_saturationpercent"
* Only available when bit 2 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1.
* We replace "profile_i0_saturation"
with "profile_i0_saturationpercent".
* This parameter will not be used
after the version number (httpversion)
is equal or greater than 0400a.
profile_i<0~(m-1)>
_sharpness
<Not
recommended to
use this>
-3~3,100 4/4 -5: Less saturation <-> 5: More
saturation
100: Use "
image_c<0~(n-1)>_saturationpercent"
* Only available when bit 2 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1.
* We replace "profile_i0_saturation"
with "profile_i0_saturationpercent".
* This parameter will not be used
after the version number (httpversion)
is equal or greater than 0400a.
profile_i<0~(m-1)>
_brightnesspercent
0~100 4/4 Set brightness in the normalized
range.
0: Darker <-> 100: Bright
* Only available when bit 0 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1.
profile_i<0~(m-1)>
_contrastpercent
0~100 4/4 Set contrast in the normalized range.
0: Less contrast <-> 100: More
contrast
© 2020 VIVOTEK INC. All Right Reserved
106
NAME VALUE SECURITY
(get/set)
DESCRIPTION
* Only available when bit 1 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1
profile_i<0~(m-1)>
_saturationpercent
0~100 4/4 Set saturation in the normalized
range.
0: Less saturation <-> 100: More
saturation
* Only available when bit 2 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1.
profile_i<0~(m-1)>
_sharpnesspercent
0~100 4/4 Set sharpness in the normalized
range.
0: Softer <-> 100: Sharper
* Only available when bit 3 of
"capability_image_c<0~(n-1)>_basicse
tting" is 1
profile_i<0~(m-1)>
_gammacurve
0~100 4/4 0: Fine-turned gamma curve by
Vivotek.
1: Gamma value = 0.01
2: Gamma value = 0.02
3: Gamma value = 0.03
...
100: Gamma value = 1
* Note: Although we set gamma value
to 100 level, but not all gamma values
are valid. Internal module will take the
closest valid one. For example, 1~45
may all be mapped to gamma value =
0.45, etc.
* Only available when
"capability_image_c<0~(n-1)>_gamm
acurve" is 1
profile_i<0~(m-1)>
_lowlightmode
<product
dependent>
<boolean> 4/4 Enable/disable low light mode.
* Only available when
"capability_image_c<0~(n-1)>_lowligh
tmode" is 1