Remove the floor liner.
Remove the two foam supports.
With the help of a colleague,
lift the coffee maker off the
base of the packaging and
place it onto a cabinet.
Lift the top carton and remove
the cup stand assembly that is
stored in it.
To prevent personal injury and/or damage to the equipment, do not lift
the equipment by yourself and do not lift it by placing your hand under
the front door!
Remove the blue shipping tape Πand
protective film from the outside of
the equpment.
Remove the keys Ž and the small
tubing brush from the cup stand, and
then install the cup stand assembly onto
the front door.
In order to comply with NSF Certification
requirements, the Eccellenza Touch must
be installed on top of the provided rubber
counter seal.
2 - Install the Counter Seal
3 - Installation Precautions
4 - Plumbing Precautions
5 - Water Filter
6 - Starting the Equipment
Default Setup Access Codes: Operator = 345678
Administrator = 234567
1 - Unbox the Equipment
We recommend the use of a high-quality water filter which eliminates most odors present in
water, and reduces the amount of particles entering the water tank.
When installing a water filter, you must refer to the water filter manufacturer’s installation instructions.
Eccellenza Touch - Quick Setup Guide (Version française au verso)
Avoid
power source. If the use of an extension cord or power bar cannot be avoided and
must be used (this is not recommended by VKI Technologies), they must be of the
heavy duty type with a minimum rating of 15 Amps.
using extension cords and power bars when connecting this equipment to a
L
as well as for adequate ventilation.
Leave ample room above the equipment to open and fill the product hoppers.
eave room at the rear of the equipment for the plumbing fitting and water hose,
E
(legs) at the bottom of the machine. Also, do not block any of the equipment's
ventilation ports.
nsure that the equipment is level and stable. This is done by adjusting the levellers
T
equipment on the same outlet/circuit.
his equipment must be installed on a dedicated 15 amp outlet. Do not install other
I
codes and regulations. It is the sole responsibility of the installer to research and to
comply with these codes and regulations.
nstallation of this equipment must comply with all local, state/provincial and federal
This equipment is designed for indoor use only and must never be installed outdoors.
I
federal codes and regulations. It is the sole responsibility of the installer to research
and to comply with these codes and regulations.
nstallation of this equipment must comply with all local, state/provincial and
A
the event water supply to brewing equipment must be shut off.
ccessibility to shut-off valve(s) must be provided and explained to customer in
F
more than one unit (including water coolers), a separate in-line shut off valve
must be installed onto each individual equipment unit.
or multi-unit locations whereby the main water conduit is supplying water to
The main power switch for the Eccellenza Touch is
located at the rear, right side of the machine.
To switch the power ON, toggle the power switch to the
" l " position.
through a quick initialization process, after which, it is
ready to be used.
The Eccellenza Touch goes
‘
Ž
Ž
Œ
Œ
7 - Fill the Coffee Bean and Powder Dispensers
Coffee 1 = French Roast
Coffee 2 = Colombian
Powder 1 = Hot Chocolate
Powder 2 = French Vanilla
Powder 3 = Milk
Open the two coffee bean dispenser lids.
Fill both of the dispensers with coffee beans.
Open the main powder dispenser lid and remove
the individual lid of the dispenser to be filled.
Fill each of the dispensers with powder.
DO NOT PACK THE POWDERS!
Replace and close all of the product dispenser lids.
To check the current water temperature in the hot water tank, remove and re-install the waste bin.
The machine displays the water temperature in the lower center of the screen during re-initialization.
8 - Checking the Water Temperature
Set the Date and Time
Enter the set up of the machine and set the correct date and time. This is extremely useful when setting
the Energy Savings features, tracking data that the equipment has collected and when reports are sent
to the operator of the equipment. The date and time settings are found in the 'General Settings' menu.
Water Levels
The Eccellenza Touch is factory preset to only dispense 8-oz, 10-oz, and 12-oz cups sizes. The water
levels can be fine-tuned in the 'Setup' menu.
Gram Throws
You may need to fine-tune the gram throws for the coffee blends and powder types you will be using
in the equipment. This ensures that the equipment delivers the best tasting beverage possible.
Product settings are adjusted in the 'Setup' menu.
Beverages
The Eccellenza Touch is preset with all of the beverages and beverage options (such as cup sizes and
strengths) enabled. Beverage options are set in the 'Setup' menu.
Notifications
The Eccellenza Touch can be configured to provide notifications about usage and consumption, counters,
faults and messages, etc. To configure the 'Notifications' feature, go to the 'Network' menu.
Change PINs for the Operator and Administrator
To prevent unauthorized access to the Eccellenza Touch programming, we highly recommend that you
change the default PIN (Personal Identification Numbers) for both the Operator and Administrator.
Both PIN numbers can be changed in the 'Security' menu.
9 - Initial Adjustments (using the Operator access code)
R
supports.
emove the four corner
Lift the box over the
machine.
VKI Publication #202357-001 rev2 - October 27, 2016
To download the Eccellenza Touch Operation and Service Manuals, please visit our web site at:
http://www.vkitech.com/documentation.html
Customer Service - 1.800.567.2951 customer.service@vkitech.com Technical Support - 1.888.854.0207 tech.support@vkitech.com
1 2
1 2 3
1 2 3
1 2
To Next Page
Need help?
General
