This document describes the VOGUE 356007 Wine Cabinet, a wine cooler designed to create a perfect temperature and humidity environment for storing wine quietly and peacefully.
Function Description
The VOGUE Wine Cabinet is a specialized appliance for storing wine bottles. It maintains a stable temperature and humidity to preserve the quality of your wine collection. The appliance is designed for household use only and is not intended for commercial or industrial use. It features a control panel for adjusting temperature settings, a child lock function, and a Fahrenheit/Celsius display interchange. The wine cooler is designed to be either built under a counter or stand alone on the floor.
Important Technical Specifications
- Product Model: 356007 JCF-20
- Voltage/Frequency: 220-240V~/50Hz
- Refrigerant/Weight: R600a/ 12g
- Effective Volume: 20L
- Loading Capacity: 7 bottles (standard Bordeaux with 750ml)
- Net Weight: 17.6kg
- Unit Dimension (WxDxH): 150x525x870mm
- Packing Dimension (WxDxH): 192x570x920mm
- Cooling Temperature Range: 5 to 20 °C.
- Recommended Storage Temperatures:
- Red Wine: 15-18°C
- White Wine: 9-14°C
- Rose Wine: 10-11°C
- Champagne & sparkling wine: 5-8°C
The appliance is designed to operate around 1 hour after being plugged in to reach its cooling temperature.
Usage Features
Installation:
The appliance should be placed on a flat, firm, and dry floor or similar noncombustible pad. It should not be exposed to rain, direct sunlight, or located in moist or damp areas. The appliance can be built under a counter or used as a standalone unit. Ensure proper ventilation by not blocking ventilation openings.
Description of the Appliance Components:
The wine cabinet consists of:
- Control Panel
- Housing
- Cover Board
- Grill
- Adjustable feet
- Lower Hinge
- Door
- Door Seal
- Upper Hinge
- Handle
Installing Handle:
To install the handle, follow these steps:
- Reveal two small holes on the door frame from the inner side by pulling out a bit of the door seal.
- Aim the handle to the holes and insert the screws from the inside.
- Screw them up with a screwdriver.
- Put the back door seal to cover the screws.
Reversing the Door:
The wine cooler is delivered with the door opening from left to right. To reverse the opening direction:
- Open the door at 90 degrees and keep it steady.
- Unscrew the two screws from the right lower hinge.
- Pull the door hinge outwards slowly, follow the arrowhead direction to get off the lower hinge.
- Continue to pull the door downwards slowly until getting it off from the top right hinge. Take off the lower hinge plate from the door axis hole.
- Screw the top right hinge and right lower hinge off from the cabinet and keep them in the polybag for needs if you want to change back left opening door in the future.
- Install the top left hinge and left lower hinge to the left side of the cabinet and delivered in a separated polybag inside the packing carton.
- Turn the door 180 degrees upside down and insert the lower hinge plate to the bottom door axis hole. Fit the top door axis hole to the top left hinge and put the lower hinge plate slowly on the left lower hinge and keep the door steady. Screw up the left lower hinge with the plate. Door reversing is finished.
Operation:
- Cleaning the Compartment: Before powering on, clean the inside of the appliance and check the drainage pipe.
- Placement: Before powering on, level the appliance on a firm and dry floor for at least 30 minutes.
- Power On: After switching on, the appliance should cool down inside after 1 hour. Otherwise, you should check the power connection.
Control Panel:
- ON/OFF: Press the button to turn the appliance on/off. In unlock state, hold the key for 3 seconds to power down, goes to stand-by mode. Hold the key again for 3 seconds to return back to normal working.
- LIGHT: Press the key to turn on or turn off the LED lights inside. In stand-by mode, the key is invalid.
- UP (Temperature Increase): Press the key once. The LED Display will flash showing the current set temperature. Continue pressing to adjust the temperature. One press increases it by 1°C. Flashing will stop and normal function will resume if no pressing has been detected for 5 seconds. The LED display will then show the actual current temperature inside.
- DOWN (Temperature Decrease): Press the key once. The LED Display will flash showing the current set temperature. Continue pressing to adjust the temperature. One press reduces it by 1°C. Flashing will stop and normal function will resume if no pressing has been detected for 5 seconds. The LED display will then show the actual current temperature inside.
- Child Lock: Press both keys (UP and DOWN) at the same time for 3 seconds to lock. Press both keys at the same time for 3 seconds to unlock.
- Fahrenheit/Celsius Display Interchange: Switch temperature display between Fahrenheit and Celsius by pressing both keys (UP and DOWN) simultaneously.
Attention:
- The cooling temperature can be set from 5 to 20 °C.
- Alarm Sound: When the system malfunction occurs and an alarm sounds, press any key on the control panel to cancel the alarm sound.
- Error Code: When the temperature sensor fails, error code displays: E1 for open circuit, E2 for short circuit.
Maintenance Features
Cleaning:
- Disconnect the appliance before cleaning.
- Clean the appliance with a soft cloth or sponge and water.
- Do not use organic solvents, alkaline detergent, boiling water, washing powder, or acid liquid.
- Do not flush the compartment of the appliance.
Items that will damage the surface of the wine cooler:
- Alkaline Detergent
- Organic Solvents
- Brushes
- Boiling Water
Power Cut:
Most power cuts can be resolved within a short time. To protect your wines during a power cut, avoid opening the door as much as possible. During very long power cuts, take the necessary measures to protect your wine.
Out of Service for a Long Time:
Remove all bottles from the appliance, unplug the appliance, thoroughly clean the inside and outside of the appliance, and store the appliance properly. If the appliance is disconnected or if there is a power cut, you must wait at least five minutes before re-starting.
Moving the Appliance:
- Cut off the power supply and unplug the appliance.
- Remove all bottles from the appliance.
- When moving the appliance, do not lean the appliance over 45°.
Troubleshooting:
The manual provides a comprehensive troubleshooting guide for common issues:
- Appliance makes lots of noise: Adjust the front foot, keep the appliance leveling, and keep the appliance a bit space from walls.
- Liquid flowing sound inside the cabinet: It is normal because of the refrigerant working inside.
- Appliance does not start: Make sure the appliance is connected to the power properly, make sure the switch is on, and the compressor re-starts after 5 minutes for a power cut.
- Compressor runs continuously: If no cold is being produced, call the retailer's after-sale service.
- Door does not seal tightly: After long time use, the door seal might get stiff & distorted partially. Heat the door seal with hot-wind blower or hot towel. The door seal gets softened and closes the door.
- Appliance does not cool sufficiently: Adjust temperature setting, keep the appliance away from sunlight or heat, and do not open the door frequently.
- Unpleasant smells inside cabinet: A little bit plastic smell for newly-buy appliance is normal and will disappear after a short time. Clean the compartment and ventilate it for a few hours.
- Condensate on the glass door a short time: Do not open the door frequently or for a long time. Do not set the temperature too low. High ambient temperature and humidity would cause condensate.
- The light is not working: Check the power supply first. Call the retailer's after-sale service if the light is broken.
Remarks:
- The net weight includes shelves and the Unit dimension is without handle on the door.
- The manufacturer reserves all the rights to change the above parameters without prior notice. Please refer to the nameplate of your appliance.
Need help?
General
To Next Page