Void BASYS B12 User Manual

Getting Started
1. Carefully unpack all the speaker cabinets, accessories and the B3 or B4 amplifier.
Check that you have all of the following :
2 B15 Sub cabinets 16 Metal corners for the B15 cabinet
2 B12 Mid Hi cabinets 2 B15 top hat blanking plates
1 B3 or B4 power amplifier 2 8 meter speaker cables
2 Speaker poles 2 2 meter speaker cables
8 Wheels for B15 cabinets (4 with brakes) 1 Screw pack
2. Mount the B12 cabinets on top of the B15 cabinets by using the supplied poles.
3. Connect the left and right outputs from your mixer to the CH1 and CH2 inputs on the rear of the B3 amplifier.
4. Connect one of the thick 8 meter speaker cables to the SUB & HI, CH1 output on the B3 amplifier. Connect the
other end of this cable to one of the speakons on a B15 cabinet. Both speakons on a B15 are wired together, so
you can connect to either speakon. Connect the other 8 meter cable to the SUB & HI, CH2 output on the B3 and
its other end to the remaining B15 cabinet in the same way.
5. Use a 2 meter speaker cable and connect one end to the unused speakon on the B15 and the other end to the
B12 cabinet. Use the lower speakon that has not been blanked off. The upper blanked off speakon is for linking to
another B12 or for connection in a permanent installation via pins +1 and -1. If you do link to other B12 cabinets
make sure you only connect via the top input speakons on both B12 cabinets.
6. Switch on your mixer, connect the power lead to the B3 and switch it on by turning the power on control clockwise.
Set both CH1 and CH2 levels controls to the same position just below maximum and set the SUB level control
around half way. Slowly turn up the output on your mixer and set it to a moderate listening level. Use the SUB
level control to either increase or decrease the level of bass to mid hi. Once the desired setting has been found,
control the systems output level from your mixer.
7. If your Basys system is going to be used in a fixed installation, the top hat on the B15 cabinet can be replaced by
the top hat blanking plate found in the accessory pack. For road or mobile use, consider fitting the wheels and metal
corners to the B15 cabinets. Screws and bolts for the corners and wheels can be found in the screw pack. An
optional road bag kit can be purchased and includes covers for two B12's and two B15 cabinets.
Precautions
Do Not connect the 8 meter cable from the SUB & HI outputs on a B3 amplifier directly to a B12 cabinet.
Always connect to a B12 via a B15 when using the SUB & HI outputs on a B3 amp.
Warranty Registration
Please take time to fill out the warranty registration form at the back of the manual and return it to Void Acoustics
Basys

Void BASYS B12 Specifications

General

Type	Portable Bluetooth Speaker
Frequency Response	60Hz - 20kHz
Max SPL	90dB
Bluetooth Version	5.0
Water Resistance	IPX5
Enclosure Material	ABS Plastic
Connectors	3.5mm AUX, USB-C
Drivers	2 x Full-range drivers

Summary

Getting Started

Initial Setup and Connections

Covers unpacking, inventory, cabinet mounting, and initial connections.

System Operation and Adjustment

Instructions for powering up the system and setting audio levels.

Installation Options and Accessories

Notes on using top hats, wheels, and metal corners for installations.

Precautions and Warranty Reminder

Cable Connection Warning

Important warning about connecting 8m cables from B3 amplifier outputs to B12 cabinets.

Warranty Registration Process

Reminder to fill out and return the warranty registration form.

System Connections

Amplifier to B15 Connection

Connect the 8 meter cable from the B3 amplifier's Sub&Hi output to a B15 speakon.

B15 to B12 Connection

Connect the 2 meter cable from the B15 spare speakon to the B12 lower speakon.

Linking B12 Cabinets

Instructions for linking multiple B12 cabinets using top input speakons.

Precautions for Use

Connection and Environmental Safety

Safety guidelines regarding environment, connections, and cable types.

Technical Specifications

B12 V2 Speaker Specs

Detailed technical specifications for the B12 V2 speaker model.

B15 V2 Speaker Specs

Detailed technical specifications for the B15 V2 speaker model.

Service and Maintenance

Authorized Service Requirements

Statement on unit complexity and need for qualified technicians.

Worldwide Service Procedures

Instructions for obtaining service and returning products.

Environmental Compliance

WEEE and RoHS Information

Information on proper disposal and product compliance.

Limited Warranty Information

Warranty Coverage and Period

Details the three-year warranty for original owners.

Warranty Violation Conditions

Conditions that void the warranty, including misuse and tampering.

Obtaining Warranty Service

Procedure for contacting Void or service centers for repairs.

Exclusions and Limitations

Disclaimers for consequential damages and warranty alterations.

Warranty Claim and Repair Process

Warranty Restrictions

Lists specific conditions that invalidate the warranty.

Return Authorization and Shipping

Instructions for obtaining return authorization and shipping.

Contacting for Repair

Guidance on how to initiate a repair request with the dealer.

Warranty Registration Form