CONTROLS
AND
EQUIPMENT
The
memories
The
system is equipped
with
two automatic
memories:
A
single
journey
memory
(1)
collects
the following data from the time the ignition
is
switched
on to
when
it is
switched
off:
Driving time, distance covered
and
fuel
used.
From
this data
the
average driving speed
and
the
average fuel consumption
are
worked out.
If
the journey
is
resumed
within
two hours
of switching off the ignition, the new figures
are automatically included
in the
calcula-
tion.
If the
journey
is
interrupted
for
more
than
two
hours,
the
stored information
is
automatically
erased.
A
total
journey
memory
(2)
stores the
data
from any number of individual journeys
up
to a
total
of 99
hours and
59
minutes
hours driving time,
a
distance
of
9999
km
and
999 litres of fuel consumed. This data
is
used
to
work
out the
consumption
and
speed
averages
for all the
individual
journeys.
If
one
of
the given figures
is
exceeded,
the
memory
is
erased
and
calculation starts
from
the
beginning again. Contrary
to the
single
journey memory, this memory
is not
erased
after
a
journey pause
of
more than
two hours.
To
call
up the
data
the
memories are se-
lected
by
means
of the
switch
A in the
wiper lever:
1 -
Single journey memory
2
-
Total journey memory
The
following data can be obtained from the
memories:
• Distance driven
• Average speed
• Average fuel consumption
• Driving time
The
amount
of
fuel used
is not
indicated.
Erasing
the
memories
With
the
ignition switched on, both mem-
ories
can be
erased separately
in
each
switch position
by
pressing switch
A
passed
the appropriate detent position
to 0
position
for
longer than one
second.
If the
battery
is
disconnected
for
any
rea-
son,
the stored information is automatically
erased.
The displays
Min
(driving
time)
Memory
1
shows
the
driving time which
has
elapsed since ignition was switched on
or the memory cancelled
is
indicated
-
see
also
"Single journey memory".
Memory
2
shows the
total
driving time
for
all
individual journeys indicated
-
see "Total
journey memory".
The
maximum time in both switch positions
is
99 hours 59 minutes. When this figure
is
exceeded
the indication starts at zero again.
Miles
(km)
-
Distance
covered
The
remarks made under "Driving time"
also
apply
in
principle
to
"Distance cov-
ered".
The maximum distance indicated
is
9999
km
or
6214 miles.
MPH
(km/h)
-
Average
speed
The
remarks made under "Average fuel
consumption"
also apply here
in
principle.
12
COCKPIT
CONTROLS
AND
EQUIPMENT
Ambient
temperature
*•*
The
measuring range
is
from
-
40 degrees
C
to +
50 °C.
When
the vehicle is stationary or only mov-
ing very slowly,
the
indicated temperature
could
be
slightly higher than
the
actual
ambient temperature due.to heat radiation
from
the
engine
or use of the
auxiliary
heater.
At ambient temperatures
of
between +4°C
and
-7°C,
a
snowflake symbol will also ap-
pear
in
the display (black ice warning).
This
symbol will flash
for
approximately
5
seconds
and will remain
lit
until
the ambient
temperature either rises above +4°C or falls
below -7°C.
Warning
If the
ambient
temperature
read-
ing
is
used
as an ice
warning,
re-
member
that
ice
can
form
on the
road
at
temperatures
of
4°C.
After switching
off
the ignition the last indi-
cated
temperature
is
stored
in
memory for
about 45 minutes.
If
the ignition is switched
on after 45 minutes or the vehicle is moved
at about
30 km/h
within
the 45
minute
period,
a
new up-to-date temperature will
be
displayed.
MPG
(Itr/100 km) -
Current
fuel
consumption
The
display shows
the
momentary
con-
sumption
at
Itr/100
km.
The
calculation
is
carried
out at
30
m
inter-
vals.
When the vehicle is stationary, the last
value
displayed
is
stored.
If the
momentary consumption function
is
chosen
after switching
on the
engine,
the
average
consumption
is
shown for the
first
30-40 metres.
With the help
of
these figures,
it
is possible
to adapt your driving style
to the
required
consumption.
MPG
(Itr/100 km) -
Average
fuel
consumption
The
average consumption
is
indicated
not
the actual consumption
at
the time
of
read-
ing.
The
average fuel consumption
is
indicated,
after switching on the ignition orerasing the
memory being
used,
after
a
distance
of
about 100 metres. Up
to
this point
a
dash
appears
instead
of
a figure. When vehicle
is
moving
the
indicated value
is
up-dated
every
5
seconds.
Memory
1
shows
the
average fuel
con-
sumption
for
the single journey.
Memory
2
shows
the
average consump-
tion
obtained during all single journeys
-
see
"Total journey memory".
Note
The
amount
of
fuel used
is
not indicated.
COCKPIT
13
To Next Page
Loading...
