EasyManuals Logo

VTech DS6621-2 Abridged User Manual

VTech DS6621-2
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
14
.ZUFMFQIPOFEPFTOPUXPSLBUBMM
Make sure the battery is installed and charged correctly. For optimum daily performance,
return the handset to the telephone base or charger after use.
Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
Make sure the telephone line cord is plugged firmly into the telephone base and the wall jack.
Unplug the electrical power to the telephone base. Wait for approximately
15 seconds, and then plug it back in. Allow up to one minute for the cordless handset and
telephone base to synchronize.
Charge the battery in the handset for up to 12 hours.
If the battery is completely depleted, charge the handset for at least 30 minutes before use.
Remove the battery and then install it again. If that still does not work, it may be necessary
to purchase a new battery.
Disconnect the telephone base from the telephone wall jack and plug in a working telephone.
If the other telephone does not work, the problem is probably in the wiring or telephone
service. Contact your telephone service provider.
Make sure there is a dial tone before dialing. It is normal if the handset takes a second or
two to synchronize with the telephone base before producing a dial tone. Wait an extra
second before dialing.
Eliminate any background noise. Mute
the cordless handset before dialing, or dial from
another room in your home with less background noise.
If you have changed your telephone service to digital service from a cable company or a VoIP
service provider, the telephone line may need to be rewired to allow all existing telephone jacks
to work. Contact your service provider for more information.
5IFBOTXFSJOHTZTUFNEPFTOPUBOTXFSBGUFSDPSSFDUOVNCFSPGSJOHTPSEPFTOPU
SFDPSENFTTBHFT
Make sure the answering system is on. When the answering system is on, the handset shows
"/40/ and the "/40/ light on the telephone base is on.
If toll saver is selected, the number of rings changes to two when there are new messages.
If the memory is full or the answering system is off, the answering system answers after 10
rings. In some cases, the answering system is affected by the ringing system used by the
telephone service provider.
Make sure the memory of the answering system is not full. When the answering machine
memory is full, it does not record new messages until some old messages are deleted.
If you subscribe to voicemail service, change the number of rings so that your answering
system answers before your voicemail answers. To determine how many rings activate your
voicemail, contact your telephone service provider.
If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
5IFNFTTBHFTPOUIFBOTXFSJOHTZTUFNBSFJODPNQMFUF
If a caller leaves a very long message, part of it may be lost when the answering system
disconnects the call after the preset recording time.
If the memory on the answering system becomes full during a message, the answering
system stops recording and disconnects the call.
If the caller’s voice is very soft, the answering system may stop recording and disconnect the call.
*BDDJEFOUBMMZDIBOHFEUIF-$%MBOHVBHFUP'SFODIPS4QBOJTIBOE*EPOmULOPXIPX
UPDIBOHFJUCBDLUP&OHMJTI
While the phone is not in use, press .&/6, and then enter
 to reset the LCD
language to English.
While the phone is on a call, press .&/6, and then enter
 to reset the LCD
language to English. Then the call ends.
$PNNPODVSFGPSFMFDUSPOJDFRVJQNFOU
If the telephone is not responding normally, put the cordless handset in the telephone base. If
this does not fix the problem, do the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base .
5. Wait for the cordless handset to synchronize with the telephone base. Allow up one
minute for this to take place.
&$0NPEF
This power conserving technology reduces power consumption for optimal battery performance.
The ECO mode activates automatically whenever the handset is synchronized with the
telephone base.
The handset shows &$0 when the ECO mode activates.
&OFSHZTBWJOHDIBSHJOHNPEF
When this mode is activated, all telephone functions, except handset battery charging, will be disabled.
5PBDUJWBUFUIFFOFSHZTBWJOHDIBSHJOHNPEF
1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are
plugged with charged batteries before proceeding.
2. While you press and hold
'*/%)"/%4&5, plug the telephone base power adapter back to the
power outlet.
3. After about 20 seconds, when the */64& light starts flashing, release '*/%)"/%4&5
and then press it again within 2 seconds.
When the phone successfully enters the energy-saving charging mode, the */64& light turns
off and all handsets display 5PSFHJTUFS)4andTFFNBOVBMalternately.
When the phone fails to enter this mode, repeat Step 1 through Step 3 above. The telephone base will
be powered up as normal if you fail to press
'*/%)"/%4&5 within 2 seconds in Step 3.
5PEFBDUJWBUFUIFFOFSHZTBWJOHDIBSHJOHNPEF
1. Unplug the telephone base power adapter from the power outlet, and then plug it back in.
Then the telephone base is powered up as normal.
2. Register your handsets back to the telephone base. See page 13 for handset registration instructions.

Other manuals for VTech DS6621-2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the VTech DS6621-2 and is the answer not in the manual?

VTech DS6621-2 Specifications

General IconGeneral
Colorsilver
Speakerphoneyes
Expandableyes
Paging Locatoryes
Volume Controlyes
Intercomyes
Incoming Lines1
New Message Indicatoryes
Caller IDyes
Call Waitingyes
Answering Systemyes
Flash Functionyes
Maximum Incoming Message Length25 minutes
Handsetsyes
Expansion Base Stations1
Expansion Handsets2, 5
Backlit Keypadyes
Keypad Locationhandset
Bluetoothyes
Remote Accessyes
Frequencydect 6.0 digital
Weight and Dimensions IconWeight and Dimensions
Depth3.5 inches
Height6.8 inches
Width5.8 inches
Net Weight16 ounces

Related product manuals