Walkera 60#B - User Manual

Overall Length: 600mm
Brush Speed Controller: WK-B20A
Battery: 11.1V 1200mAh/1500mAh Li-Po
Specifications:
Main Rotor Dia. : 620mm
Tail Rotor Dia. : 145mm
Brush Main Motor : 380PF
Brushless Speed Controller: WK-WST-30A
Brushless Main Motor : WK-WS-26-001
Transmitter: WK-2601
All-up Weight: 620-640g (Battery included)
Gyro: WK-G011
Receiver: RX-2701
Servo: wk-7.6-3 / weight 8.4g / speed 0.12sec/60e (4.8V) / torque 1.4kg/cm (4.8V) / dimension 22.5
h 11.5h 24mm
Servo: wk-7.6-H / WK-7601 / weight 6.0g / speed 0.08sec/60e (4.8V) / torque 0.8kgf.cm (4.8V) / dimension 21.5
h 11.8h 21.7mm
Features:
1) CCPM mixing control system and collective pitch control system make perfect 3D maneuvers such as rolls, inverted, and
swoop flights.
2) 60#B The compact structure characterized by metal main frame and metal tail boom makes the helicopter more stable.
Easy-to-be mounted parts like servo are used.
3) 60#B Highly efficient bevel wheel design is used in mesh between main gear and motor gear.
4) Tail blades driven by belt provide easy adjustment, stable flight, and low noise.
6) New 2.4G technology, with the functions of identification and precise code pairing, can allow many RC aircrafts to fly
in the same field and same time.
5) Equipped with high performance brush/brushless motor, the flight time will be up to 6 to 9 minutes at 11.1V 1200mAh/1500mAh
LiPo battery pack, depending on your flight mode.

Summary

02 Matters needing attention

2.2 Safety needing attention

Crucial safety precautions and warnings for operating the RC helicopter.

2.3 Attention before flight

Pre-flight checks and procedures to ensure safe and proper operation.

05 Instruction and attention of WK-2601 transmitter

5.3 Instruction and attention of transmitter

Guidance on battery mounting, code pairing, and attention points for the transmitter.

5.3.3 Code pairing and its attention

Procedure for code pairing the transmitter with the receiver and associated precautions.

06 Instruction and attention of RX2701

6.3 Channel connection and adjustment of receiver

Details on connecting servos and ESC to receiver channels and adjusting receiver settings.

07 Instruction of ESC

08 Instruction and attention of servo

09 Instruction and attention of gyro

10 Instruction and attention of GA005 balance charger

10.6 Matters needing attention

Critical safety and operational precautions for using the GA005 balance charger.

11 Steps of flight

11.2 Center of Gravity adjustment

Procedure for adjusting the helicopter's center of gravity for stable flight.

11.4.2 Matters needing attention

11.4.3 Troubleshoot of receiver LED flashing

Troubleshooting guide for issues where the receiver LED continuously flashes after connection.

11.5 Adjustment before flight

Essential pre-flight adjustments and checks to ensure optimal performance and safety.

11.5.1 Swashplate Adjustment

Procedure for inspecting and adjusting the swashplate for correct flight control, including bell crank alignment.

11.6 Adjustment of exponential parameter of servo

Guide to adjusting servo exponential curves for improved flight handling and response.

11.7 PIT adjustment

Instructions for adjusting the PIT angle using transmitter knobs for controlled ascent and descent.

11.7.1 PIT parameters in normal mode

Steps for adjusting PIT parameters in normal flight mode, using a pitch gauge for accuracy.

11.7.2 PIT parameter in 3 D mode

Steps for adjusting PIT parameters specifically for 3D flight mode.

11.8 Adjustment of receiver

Guide to adjusting receiver settings, specifically the servo extent.

11.8.1 Adjustment of servo extent

11.9 Gyro sensitivity and rudder mixing

Tuning gyro sensitivity and rudder mixing to stabilize flight and correct shaking.

11.10 Main rotor blades adjustment

Procedures for adjusting main rotor blades for weight balance, gravity center, and tracking.

11.10.2 Inspection and gravity center adjustment of main rotor blades

How to inspect and adjust the gravity center of main rotor blades for balance.

11.10.3 Tracking inspection

Method for inspecting main rotor blade tracking to ensure proper alignment during spinning.

11.10.4 Adjustment of blade tracking

Causes and methods for adjusting main rotor blade tracking to correct misalignment.

11.11 Tail rotor blades adjustment

Steps for inspecting and adjusting tail rotor blades and servo linkages for symmetry.

11.11.2 Adjustment of tail rotor blades

13 FAQ

Appendix 2 - Trimming the Flight Actions

Appendix 3 - Flight Practice

Walkera 60#B Specifications

General

Brand	Walkera
Model	60#B
Category	Motorized Toy Car
Language	English