EasyManua.ls Logo

Warn HUB - User Manual

Warn HUB
9 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Quick Start Guide
AXON WARN® HUB RECEIVER
1.
WARN HUB
Download the WARN® HUB App
from the App Store or Google Play.
KIT CONTENTS BEFORE YOU BEGIN
MOUNT
Data rates may apply.
Apple is a trademark of Apple Inc., registered in the U.S. and in other countries. App
Store is a service mark of Apple Inc.
Google Play is a trademark of Google Inc.
2.
3.
Determine mounting location and wire routing path.
Recommendation: Under vehicle hood, on vehicle frame
or along other wiring bundles. Avoid sharp edges, heat
and moving parts.
Using the included zip-ties, mount HUB Receiver rmly
to vehicle.
Route the plug ends of the HUB to the vehicle accesso-
ry wire harness connections. NOTE: Make sure to route
wires/cables away from sharp edges, heat and moving
parts.
4.
NOTE: Zip tie cables to vehicle in regular intervals to keep cables secure and
in place.
I
II
III
0
9.
8.
Quick Start Guide
AXON WARN® HUB RECEIVER
5.
• Disconnect the vehicle accessory wire harness
from the winch control switch.
• Plug one HUB Receiver connector into the winch
control switch.
• Plug remaining HUB Receiver connector into the
accessory wire harness.
7.
Turn vehicle power on.
NOTE: The HUB Receiver is active when
the yellow light is on.
When light on the HUB Receiver
turns green, you are connected.
Continue following the instructions
through your app.
6.
Continue
You are now connected!
WIRE
PAIR/CONNECT
CUSTOMER SERVICE
WARN INDUSTRIES, INC. 12900 S.E. Capps Road,
Clackamas, OR USA 97015-8903, 1-503-722-1200
Customer Service: 1-800-543-9276
Dealer Locator Service: 1-800-910-1122
POWER
NOTE: Image
shows HUB
Receiver
connection at
switch. The
HUB Receiver is
also adaptable
to winch
connection if
preferred.
Press and hold button on HUB
Receiver until blue light ashes
(approximately 2 seconds) and then
release button.
Open app on phone and follow
prompts.
I agree to the latest
Privacy Policy,
Terms of Use and
Safety Agreement
x
Continue
Winch
Control
Switch
HUB Receiver
Accessory Wire Harness

Table of Contents

Other manuals for Warn HUB

Preview: General Safety/ Tips/Trouble Shooting/ Customer Service Guide
General Safety/ Tips/Trouble Shooting/ Customer Service Guide18 pages

Questions and Answers

  • D
    Daniel MannJul 28, 2025
    How to troubleshoot a Warn HUB Receiver that is not operating?
    • B
      bondlindsayJul 28, 2025
      If your Warn Receiver-controlled winch isn't working, there could be a few reasons. First, ensure the vehicle is turned on and that all wiring connections (contactor, control pack, and ground wire) are correctly connected and secure. Also, check the vehicle battery connections. If applicable, confirm the winch remote plug is properly connected. Another potential cause is the connection between the HUB App and HUB Receiver. Verify the HUB Receiver’s LED is green.
  • S
    Steven BartonAug 7, 2025
    What to do if Warn HUB will not pair or connect?
    • J
      Johnny CraigAug 7, 2025
      If your Warn Receiver isn't pairing or connecting, several factors could be at play. Ensure your smart device is within range of the receiver. Interference from other devices can also be a problem, so disconnect from other Bluetooth devices. Verify that Bluetooth is turned on in your smart device. A disrupted pairing may require you to reset the receiver and repair the connection. Also, make sure the app is open and that no other smart devices are connected to the receiver. Finally, confirm that the vehicle power is on and the HUB receiver is plugged into the winch remote socket.
  • L
    Linda AnthonyAug 17, 2025
    Why does my Warn HUB Receiver have intermittent operation?
    • J
      Justin GreenAug 17, 2025
      Intermittent operation of your Warn Receiver can stem from several causes. A poor signal may be the issue, so try getting closer, relocating the receiver away from obstructions like batteries or engines, maintaining a line of sight to the vehicle with the receiver, and avoiding sources of radio interference such as power lines or other radios. Low battery voltage can also cause this, so allow the vehicle to charge before using and check battery connections. Note that the WARN HUB receiver is not designed for continuous use with some legacy solenoid control packs. Overheating of the HUB can also lead to intermittent operation; if this is the case, move the HUB to a cooler location on the vehicle.

Summary

Kit Contents

Before You Begin

Download WARN HUB App

Download the WARN HUB App from the App Store or Google Play to get started.

Mounting the HUB Receiver

Determine mounting location, mount receiver firmly using zip-ties, and route cables safely.

Wiring Connections

Connect Wire Harnesses

Disconnect vehicle accessory harness, then connect HUB Receiver to winch switch and accessory harness.

Powering On

Activate HUB Receiver

Turn vehicle power on. The HUB Receiver is active when its yellow light is illuminated.

Pairing and Connection

Initiate Pairing Mode

Press and hold the HUB Receiver button for about 2 seconds until the blue light flashes.

Connect via Mobile App

Open the WARN HUB app on your phone and follow the on-screen prompts to establish connection.

Confirm Connection

Connection is confirmed when the HUB Receiver light turns green; continue following app instructions.

Warn HUB Specifications

General IconGeneral
BrandWarn
ModelHUB
CategoryReceiver
LanguageEnglish