EasyManua.ls Logo

Waterco 25A - User Manual

Waterco 25A
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.waterco.com
WARNING
!
ELECTROCHLOR LCD
CHLORINATORS
Owners Manual
25A SC Self-Clean
30A SC Self-Clean
This equipment must be installed and serviced by a qualified technician.
Improper installation can create electrical hazards which could result in property
damage, serious injury or death. Improper installation will void the warranty.
Note :
For Tariff 33 installation best to connect Electrochlor LCD to normal power
for at least 12 hours to fully charge the batteries. Otherwise Electrochlor
LCD can be just plugged into power to set the time and programs.

Table of Contents

Questions and Answers

  • M
    Megan JacksonAug 9, 2025
    Why does my Waterco Water System show 'FL' and the Filter/Salt LEDs are off?
    • F
      floreschristopherAug 9, 2025
      If the Waterco Water System displays 'FL' and both the Filter and Salt LEDs are off, it could be due to several reasons: * The pump might not be connected, causing no water flow in the cell. * There might not be enough salt in the water. * The valves could be closed. To resolve this, ensure the pump is connected to allow water flow, add the necessary amount of salt, and open the valves. Also, clean the filter and check the water level. If back washing is in progress, change to normal filtration. Another potential cause is a dirty flow detector, which should be cleaned. If none of these steps work, there may be an electronic fault, and the unit should be returned to the distributor for repair.
  • B
    Barbara MorrowAug 14, 2025
    What to do if Waterco Water System displays F0, F1 or F2 and Control set at maximum?
    • T
      Thomas ShawAug 14, 2025
      If your Waterco Water System displays 'F0, F1 or F2' and the control is set at maximum, it could be due to low salt levels, water temperature below 15°C, or a dirty cell. You can try to add salt and increase the water temperature to 20°C or above, and clean the cell. If the issue persists, it may indicate an electrical fault, requiring you to return the unit to the distributor for repair.
  • A
    Anthony Rice PhDAug 19, 2025
    Why is the chlorine level low in my Waterco Water System pool?
    • C
      corey03Aug 19, 2025
      If the chlorine level in your Waterco Water System is low, there are a few potential reasons. The operating time might be too short, or the production control could be set too low. You might also have low salt levels, or incorrect pool chemistry. To address this, try increasing the operating time and setting the production higher. Add the required amount of salt, and have your water tested to correct the pool chemistry.
  • R
    Richard DunnAug 25, 2025
    How to troubleshoot a Waterco Water System that does not operate?
    • J
      Joshua SmithAug 25, 2025
      If your Waterco Water System unit isn't operating, check if it's receiving electrical power. Ensure the power is connected, inspect the fuse, and switch on the Electrochlor LCD. Also, verify that the pump is properly connected.
  • R
    Renee MarshallAug 29, 2025
    What does error code F0 mean on my Waterco Water System?
    • M
      Michele WalkerAug 29, 2025
      If the Waterco Water System displays 'F0', it may be because back washing is in progress, in this case return to normal operation. Alternatively, the cell may have a buildup of calcium or the cell coating may be deteriorating, requiring you to clean or replace the cell.
  • X
    xoliverSep 3, 2025
    Why is my Waterco Water System not keeping time?
    • J
      Jason McbrideSep 3, 2025
      If your Waterco Water System is not keeping time, it could be due to the time clock setting, a power outage, or the battery not being connected. Reset the clock and connect the battery link. If the battery is flat, it will require a reset after a blackout. If the issue persists, there may be an electrical fault, and the unit should be returned to the distributor for repair.

Waterco 25A Specifications

General IconGeneral
BrandWaterco
Model25A
CategoryWater System
LanguageEnglish