Need help?Do you have a question about the Waterstone 30101 and is the answer not in the manual?
Congratulations on purchase; system provides years of service with proper maintenance.
Steps before installation: turn off water, check codes, inspect supplies, avoid petroleum products.
Lists adjustable wrench and utility knife as required tools for installation.
Unit can be mounted to cabinet or wall using back holes and screws.
Check tubing, retainer clip, flush system, check for leaks.
Lists system life, filter stages, dimensions, weight, pressure, and temperature specifications.
Warranty applies only if installed per instructions; excludes improper parts/alterations/misuse.
Manufacturer not responsible for lost time, inconvenience, or other consequential damages.
Owner must perform scheduled maintenance; neglect or abuse invalidates warranty.
Implied warranties of merchantability and fitness expire one year after purchase.
Grants specific legal rights that vary by state.
The Waterstone Multi-Stage Filtration System (Model #30101) is a comprehensive under-sink water treatment solution designed to provide clean, filtered drinking water. This system is engineered for durability and ease of use, offering years of trouble-free service when properly maintained. It is intended for installation by a licensed professional, such as a contractor or plumber, due to the need for familiarity with standard sink plumbing and the proper use of common hand and power tools. Improper installation could lead to water damage from leaks or flooding. The system is designed for use with potable water and should not be used with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
The Waterstone Multi-Stage Filtration System is a three-stage filtration unit that connects to a dedicated cold-only filtration faucet, typically installed at the kitchen sink. Its primary function is to remove various impurities from drinking water, enhancing its taste, odor, and overall quality. The system operates by directing cold water from the angle stop through a series of filters before it reaches the dispensing faucet. This multi-stage approach ensures thorough filtration, addressing different types of contaminants at each stage. The filtered water is then dispensed through a separate faucet, providing a convenient source of purified water for drinking and cooking. The system is designed to integrate seamlessly with existing under-sink plumbing, utilizing standard connections.
The system is designed for straightforward operation once installed. To begin using the system, the cold water supply to the angle stop must be turned off, and water pressure relieved by opening the faucet handle. The cold water supply hose from the kitchen faucet is then removed from the angle stop. A supply line connector is attached to the angle stop, and the cold water supply hose is reconnected to this connector. The green hose from the filtration unit is inserted into the supply line connector, ensuring a secure fit. The blue hose from the filtration unit is connected to the faucet shank using a compression nut and ferrule, which are tightened with a wrench.
After all connections are made, the system requires activation and inspection. This involves checking all tubing connections to ensure they are firmly seated and verifying that the cartridge retainer clip is properly installed with the slide locks fully engaged in the frame slots. The retainer clip is crucial for long-term, unattended operation of the system, as failure to keep it properly engaged could lead to accidental leaks and flooding. Once these checks are complete, the dispensing faucet at the sink is opened, followed by the feed water valve to the system and then the angle stop. The system should be observed for several minutes to detect any leaks.
During the initial activation, the faucet should be allowed to run for at least three minutes. It is normal to observe a small amount of carbon fines in the water during this initial flush, and the water may also appear milky due to trapped air in the system. If practical, inverting the unit until air ceases to purge from the faucet can help. After the three-minute flush, the faucet is closed, and fittings are re-checked for leaks. Once these steps are completed, the system is ready for use, providing filtered water on demand through the dedicated faucet.
Maintenance of the Waterstone Multi-Stage Filtration System, specifically cartridge replacement (Model #30102), is designed to be quick and easy, requiring no special tools. Regular maintenance is essential to ensure the system's efficiency and to maintain high water quality. Cartridges in this system must be replaced every 6-12 months.
The cartridge replacement process begins by turning off the cold water at the angle stop or the feed water valve to the system. Next, water pressure needs to be relieved by opening the faucet handle of the filtration faucet. To access the cartridge, the sides of the system's cover are squeezed to remove it from the front of the unit. Once the cover is off, the retaining clip is squeezed and removed. The old cartridge can then be pulled off the system evenly from the top and bottom connectors. The used cartridge should be disposed of properly.
To install a new cartridge, it is gently rocked from side to side while being inserted until the cartridge tubes are properly engaged in the unit connectors. It is crucial to re-install the retaining clip, ensuring that its slide locks snap into place through the slots. If the clip does not snap easily into place, it indicates that the cartridge is not fully inserted into the connectors. Proper installation of the retaining clip is vital, as failure to do so can result in accidental leaks and flooding. After replacing the cartridge and re-installing the retaining clip and cover, the water supply can be turned back on, and the system can be flushed as described in the initial activation steps to ensure proper function and remove any air or loose carbon fines. This simple, tool-free process ensures that the system continues to deliver high-quality filtered water with minimal effort.
General| Brand | Waterstone |
|---|---|
| Model Number | 30101 |
| Filtration Technology | Activated Carbon |
| Filter Life | 6 months |
| Filter Contaminants | Chlorine, Taste, Odor |
To Next Page