2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403
www.waterwayplastics.com • waterway@waterwayplastics.com
810-0079.1008
© Copyright 2008 Waterway Plastics
STANDARD SYSTEM
OWNER’S MANUAL
If the pressure gauge on your lter reads 5 PSI or higher than the
original starting pressure, the lter needs to be cleaned. The ClearWater
II D.E. Filter System features the exclusive 1-2-3 Safety Locking System
to ensure safe and simple lter maintenance.
1. Turn o pump. WARNING: Never attempt to clean lter while
pump is running. This is a pressurized vessel. It could cause
severe injury or harm to your person. Plug skimmer and pool
return lines or drain pool water level to below pool return line.
2. Slowly open the air release knob on top of lter until the pressure
gauge reads “0”. Open drain cap at bottom of lter and allow water
to ow.
3. Press the yellow safety latch on the underside of the locking nut and
turn the nut counterclockwise to remove the lid. Rinse the D.E.
element with a garden hose. There is no need to remove the element
from the lter.
4. Reassemble lid and follow start-up procedures from original
instructions.
My Original Starting Pressure is ________ PSI (Pounds per
Square Inch). I should clean the lter at ________ PSI.
Waterway Plastics manufactures its products and equipment in accordance
with very high standards of workmanship. We use the best materials available
and maintain the highest quality procedures practical in the industry. In
accordance, Waterway warrantys its products as follows:
All plastics parts such as jets, valves, skimmers,manifolds, suctions, lights,
and other plastic components manufactured by Waterway will be replaced or
repaired, if the defects are determined by Waterway to be the responsibility of
Waterway Plastics, for a period of three years from the date of installation. The
warranty does not cover lter cartridges, D.E. grids, O-rings, pressure gauges,
pump seals, light bulbs or any parts not manufactured by Waterway. Warranty
applies to OEM’s and Distributors of Waterway Products.
The Supreme and Hi-Flo Pumps will receive limited warranty from any defect
in material or workmanship for one year from the date of manufacture. This
includes the motor but not the motor seal.
All thermoplastic molded lter bodies and rotational molded sand lter bodies
have a warranty of ten years, warranted on a pro-rata life basis.If a defect
becomes apparent during the rst year, the body will be exchanged for a
new body if the defects are determined by Waterway to be the responsibility
of Waterway Plastics. If a defect becomes apparent after the rst year from
the date of manufacture which, in the opinion of Waterway, will require
replacement, the body will be exchanged for a new tank on an adjusted
service pro-rata life basis. Charges to the owner, on the pro-rata life basis, will
be determined by the actual number of months installed beginning with the
date of installation.
Products that fail or become defective during the warranty period, except as a
result of improper installation, bad water chemistry, accidents or negligence
on behalf of the owner, freezing, earthquakes, re oods, or other acts of
nature, shall be repaired or replaced at Waterway’s option without charge
to the owner. This process will be completed within 90 days of receipt of the
defective product barring delays caused by the acquisition of component parts
not manufactured at our facility.
To obtain warranty replacements or repair, defective products should be
returned (transportation paid) to the place of purchase, or to Waterway. It
should include a description of the defect and the circumstances surrounding
the incident or problem.
Waterway shall not be responsible for cartage, removal and/or reinstallation
labor, or any other such costs incurred in obtaining warranty replacements.
Warranty applies to OEM’s and Distributors of Waterway Products.
This warranty gives you specic legal rights. You may also have other rights
which very from state to state.
CLEANING INSTRUCTIONS
LIMITED WARRANTY
To Next Page
Need help?
General
