Weed Eater W25SB User Manual

ASSEMBLE SHAFT (MODELS WITH
KNOCKDOWN SHAFT)
a WARNING: To avoid personal injury or damage
to the unit, turn the unit off when assembling or
disassembling the shaft.
CAUTION: When assembling or disassembling the shaft,
place the unit on a at surface for stability.
1. Align the tab on the coupler (A) with the slot on the
lower tube (B).
2. Press the lower shaft into the coupler until the tube
ends are touching (C).
3. Install the coupler knob (D) on the same side as the
screw head and tighten securely.
CAUTION: To avoid personal injury or damage to the unit,
periodically check to ensure the tube ends are touching
and the knob is tight.
ADJUST HANDLE
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an upright position; retighten
wing nut.
ATTACH SHIELD
1. Mount shield to bracket by inserting TAB (A) on shaft bracket into
SLOT (B) in shield.
2. Rotate shield until bolt goes through bracket.
3. Attach wing nut (C).
C
A
B
FILL TANK
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of gasoline for a
50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
PLACE IN STARTING POSITION
Hold trimmer rmly on the ground (as shown).
START COLD ENGINE
Press the primer bulb 6 times rmly.
Move the choke lever to the full choke
(bottom) position.
Squeeze the throttle trigger while pulling
the starter rope handle 6 times rapidly.
Move the choke lever to the half choke
(middle) position.
Squeeze the throttle trigger while pulling
starter rope rapidly until the engine starts,
but no more than 6 pulls.
If the engine does not start, see
“STARTING A FLOODED ENGINE” in the
“OPERATION” section.
Move the choke lever to the run (top)
position.
Allow the engine to warm up for one minute.
START HOT ENGINE
Follow steps 4-6 in
START COLD ENGINE.
LT25NCOP
LT25NSOP
NOTE: Your product may differ slightly from the item shown.
Quick-Start Guide
a WARNING: Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
W25CB / W25CBK
W25SB / W25SBK
590203801 Rev. A 2017-02-24

Weed Eater W25SB Specifications

General

Type	String Trimmer
Power Source	Gasoline
Engine Type	2-Cycle
Engine Displacement	25cc
Cutting Width	16 inches
Line Diameter	0.095 inches
Shaft Type	Straight
Cutting Swath	16 inches
Fuel Tank Capacity	0.5 liters
Handle Type	Loop Handle

Summary

Quick-Start Guide

ASSEMBLE SHAFT (MODELS WITH KNOCKDOWN SHAFT)

FILL TANK

START ENGINE

Procedures for starting a cold or hot engine.

SAFETY RULES

OPERATOR SAFETY

Guidelines for safe operation and personal protective equipment.

UNIT / MAINTENANCE SAFETY

Safety precautions related to unit maintenance and repair.

FUEL SAFETY

Rules and precautions for handling and storing fuel.

CUTTING SAFETY

ASSEMBLY

SHAFT ASSEMBLY (MODELS WITH KNOCKDOWN SHAFT)

OPERATION

BEFORE STARTING ENGINE

FUELING ENGINE

STARTING PROCEDURES

STARTING A COLD ENGINE

Detailed steps for starting a cold engine.

STARTING A HOT ENGINE

Steps for starting a hot engine.

STARTING A FLOODED ENGINE

OPERATING TIPS

CUTTING METHODS

MAINTENANCE

CLEAN AIR FILTER

REPLACE SPARK PLUG

SERVICE AND ADJUSTMENTS

LINE REPLACEMENT

REPLACING THE TRIMMER HEAD

IDLE SPEED ADJUSTMENT

TROUBLESHOOTING TABLE