WARNING
Do not use for commercial use. User must read and understand the
operator’s manual for their pressure washer before using this accessory
to reduce the risk of injury. Before beginning any cleaning activity,
spray the pressure stream in a safe direction to make sure that all
accessories are connected properly in order to minimize the danger
of injury or property damage. Fits most pressure washers. Before
using this attachment, make sure it is compatible and is correctly
installed. Risk of uid injections. Do not point at people, pets, electrical
devices, or the unit itself. Wear eye protection designated to conform
with ANSI Z87.1. Before adding, replacing, or modifying accessories,
turn off the pressure washer, release the water pressure in the trigger
handle, and lock the trigger handle’s lock out (if one is provided with
your pressure washer). Use only with cold water and only outdoors.
Store the accessory indoors. Save these guidelines. Use them to train
other users and refer to them frequently. Give the user of the tool these
instructions as well.
PRODUCT SPECIFICATIONS
Connection ..................................................1/4 in. Quick Connect Plug Inlet
Width of Deck ....................................................................................... 12 in.
Maximum Pressure..................................................................up to 2500 psi
Minimum Pressure............................................................................1400 psi
Maximum Water Flow ...................................................................... 2.3 GPM
Minimum Water Flow ....................................................................... 1.1 GPM
Maximum Water Temperature ..............................................................140°F
APPLICATIONS
You may use this product for the purpose(s) listed below:
l Cleaning decks, sidewalks, and driveways
INSTALLING THE SURFACE CLEANER
See Figure 1.
l If necessary, remove the nozzle from the end of the lance.
l Pull back the quick-connect collar and insert the inlet adapter. Push the
quick-connect collar forward to lock.
NOTE: Be sure the surface cleaner is securely locked into the lance before
use.
WARNING
Only use the surface cleaner on at, horizontal surfaces. To reduce the
risk of injection or injury, never lift the surface cleaner from the cleaning
surface while operating the pressure washer.
USING THE SURFACE CLEANER
See Figure 2.
l Place the surface cleaner on the horizontal surface being cleaned and start
the pressure washer.
l Squeeze the trigger and move slowly allowing the unit to clean the surface
NOTE: Swirling or striping in the cleaned surface indicates you may be
moving too quickly. If a slower pace doesn’t stop the condition, the surface
cleaner nozzles may be clogged. See Nozzle Maintenance to clean the
nozzles.
WARNING
Avoid striking any raised obstacles while using the surface cleaner as
damage may occur to the unit. If contact occurs and a higher vibration
of the unit begins during use, release the trigger and discontinue use.
Continuing use could result in serious injury or damage to the unit.
NOZZLE MAINTENANCE
See Figure 3.
The surface cleaner comes assembled. The nozzles are approved for use
with pressure washers operating at 1400 to 2500 PSI with a maximum ow
rate of 2.3 GPM (1.1 GPM minimum).
A pulsing sensation felt while squeezing the trigger and/or a higher vibration
in the surface cleaner may be the result of a clogged or dirty nozzle.
FIG. 1
FIG. 2
A - Inlet adapter [adaptador de entrada, adaptateur d’entrée]
B - Quick connect coupler [acoplador de conexión rápida, coupleur à connexion
rapide]
A
B
Service Hotline: (855) 944-3571
777 Manor Park Drive, Columbus, OH 43228
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by MWE Investments, LLC.
© 2023 MWE Investments, LLC All Rights Reserved.
l Turn off the pressure washer and shut off the water supply. Place unit on
the ground and pull the trigger to release the water pressure in the lance.
l Pull back the quick-connect collar to disconnect the surface cleaner from
the lance.
l Use a nozzle cleaning tool or a ne needle to free any foreign materials
that are clogging or restricting the nozzle.
l Use a garden hose to back-ush the nozzle and force out the debris.
NOTE: Never point the nozzle outlet at your face.
l Reconnect the surface cleaner to the lance.
l Turn on the water supply and start the pressure washer to resume cleaning.
REPLACING THE HIGH-PRESSURE FILTER
See Figure 4.
If the water still doesn’t ow freely after cleaning the deck nozzles, it may be
necessary to replace the high-pressure lter. Replacement lters are available
by calling our Service Hotline at (855) 944-3571.
l Turn off the pressure washer and shut off the water supply. Place unit on
the ground and pull the trigger to release the water pressure in the lance.
l Disconnect the surface cleaner from the lance.
l Insert a slotted screwdriver into the slot of the lter as shown and turn
counterclockwise to remove.
l Insert the new lter into the inlet plug.
l Turn the lter clockwise with the slotted screwdriver until it is inside the
inlet adapter and no longer visible above the top of the adapter.
REPLACEMENT PARTS
Replacement parts are available from our Service Hotline at (855) 944-3571.
Nozzle......................................................................................... 02000600-0
High-pressure Filter .................................................................... 03000434-0
PWSC12 SURFACE CLEANER
FOR WESTINGHOUSE PRESSURE WASHERS UP TO 2500 PSI
FIG. 3
A
B
FIG. 4
A - Nozzle [boquilla,
buse]
B - Nozzle cleaner
[limpiador de
boquillas, nettoyeur
de buse]
05000554 10/12/23 (REV:01)
To Next Page
Need help?
General
