Westinghouse SR74FA02C-08 User Manual

E
REPLACING THE BATTERY
TROUBLE SHOOTING
INSTRUCTIONS
Tools Required
Phillips-head
Screwdriver
Pencil
Electric drill
drill bit size:
ø7.5mm (3/10 in.)
INSTALLATION
Drill two holes.
1 Marking the location
Measure the width of two holes on the back of the mounting plate
(Part D) and mark holes for the 2 screws (Part A) on the surface.
The distance between the two holes is 2.36in. (60mm).
Mark the location where you want to mount the light fixture (Part C).
2 Mounting the light xture
Insert the wall anchors (Part B) so they are flush with the surface.
x
x
2.36in. (60mm)
FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN
THE “ON” POSITION TO FULLY CHARGE THE BATTERY.
The intelligent solar LED motion activated light measures the available battery power capacity and adjusts the light's performance to
maximize runtime.
Hardware Included
Parts
(B) Wall Anchor X 4(A) Screw X 4
(C) Light Fixture X 2 (D) Mounting Plate X 2
Secure the mounting plate (Part D) in place with the screws (Part A).
Mount the light on the mounting plate (Part D) by aligning the holes
on the back of the light to the knobs on the front of the mounting plate.
Align, insert, and slide down to lock in place.
B
A
D
C
Slide the power switch to the "OFF" position.
Use a Phillips head screwdriver to remove the
4 screws holding the battery cover in place.
Replace old battery with a new 3.7V, 2000 mAh
lithium (18650) rechargeable battery.
Replace the battery cover by aligning it properly
and replacing the 4 screws removed earlier.
Slide the power switch to the “ON” position.
For optimal performance, allow light xture to charge
in full sunlight for 8-12 hours, to fully charge the
battery.
If light doesn’t turn on, check the
battery to ensure that it is making
secure contact with the terminals.
If this doesn’t work, replace with a
new battery.
SOLAR LED AREA WALL LIGHT WITH MOTION SENSOR
ITEM: SR74FA02C-08
NOTE: Light fixture will stay on 30 seconds when triggered by motion and revert back to standby mode of 20 lumens until motion is detected.
For best performance, mount the light a minimun 6 feet (1.8 m) above the ground. Detection range is 26 feet (8 m), detection angle is 120°.
Light fixture uses radio frequency technology to link, and should not be greater than 98 feet (30 m) between the neighboring/adjacent lights.
When one light is triggered by motion both lights will activate. The package includes 2 lights. These 2 lights are factory linked, and can not be
linked with more of the same type light or any other lights.
Power Switch
Screws
Battery Cover
Battery

Westinghouse SR74FA02C-08 Specifications

General

Brand	Westinghouse
Model	SR74FA02C-08
Category	Accessories
Language	English

Summary

Installation Guide

Tools Required for Installation

Lists essential tools like a pencil, Phillips-head screwdriver, and electric drill with a specific bit size for mounting.

Hardware Included in Package

Details the hardware provided, including screws (A) and wall anchors (B), for securing the mounting plates.

Parts Identification

Identifies the key components of the light fixture, such as light fixtures (C) and mounting plates (D), for assembly.

Marking Installation Location

Instructions on measuring and marking the mounting surface for two holes spaced 2.36 inches (60mm) apart.

Mounting the Light Fixture

Steps for inserting wall anchors, securing the mounting plate, and attaching the light fixture by aligning and sliding.

Troubleshooting and Battery Replacement

Troubleshooting Light Issues

Guidance on checking battery contact and replacing the battery if the light does not turn on.

Replacing the Battery

Procedure to replace the battery, including switching off power, removing screws, and inserting a new 3.7V lithium battery.

Regulatory and Safety Information

FCC Warning and Compliance

Details FCC compliance for Class B digital devices, including measures to correct harmful interference.

RF Exposure Limits

Specifies that the equipment complies with FCC radiation exposure limits, requiring minimum 20 cm distance.

Battery Disposal Warning

Advises against disposing of lithium batteries in municipal waste or fire, and specifies proper disposal methods.