Whirlpool 3LWTW4740 - User Manual

Other manuals for Whirlpool 3LWTW4740

Questions and Answers

M
Michael SmithAug 17, 2025
Why won't my Whirlpool 3LWTW4740 Washer run or fill?
- S
  Sharon BradyAug 17, 2025
  If your Whirlpool Washer isn’t running or filling, make sure the power cord is plugged into an earthed outlet and that you're not using an extension cord. Also, ensure the outlet has power. Check the circuit breaker and fuses, and remember that the lid must be closed for the washer to run. The washer may pause during certain cycles, so avoid interrupting it. If problems persist, consult an electrician.
M
Madeline WatersAug 19, 2025
What to do if my Whirlpool 3LWTW4740 Washer is not draining or spinning?
- T
  Terry OsbornAug 20, 2025
  If your Whirlpool Washer isn't draining or spinning, it might be due to small items caught in the pump, an unbalanced load, or incorrect drain hose installation. First, ensure pockets are empty and use garment bags for small items. Rearrange the load evenly in the basket. Check the drain hose to ensure it’s properly installed and not clogged. Also, too much detergent can cause this issue, so always measure and follow detergent directions. To remove extra water, select Drain & Spin; to remove extra suds, select Rinse & Spin without adding detergent.
S
Stacey RayAug 22, 2025
What to do if the lid locked light is flashing on my Whirlpool Washer?
- C
  cjordanAug 23, 2025
  If the lid locked light is flashing on your Whirlpool Washer, ensure the lid is fully closed, as the washer won't start or fill if it's open. If you've recently paused the cycle, the lid may remain locked until the basket completely stops spinning, which can take several minutes, especially with large or heavy loads.
M
matthewsjesseAug 25, 2025
Why is my Whirlpool 3LWTW4740 load not rinsed properly?
- M
  mackdawnAug 26, 2025
  If your Whirlpool Washer load isn't rinsing properly, check the water supply to ensure both hot and cold inlet hoses are connected correctly and that water is flowing to the inlet valve. Make sure the inlet valve screens aren't clogged and that there are no kinks in the hoses. Using too much detergent or overloading the washer can also prevent proper rinsing. Load garments loosely, use a cycle designed for the fabrics, and choose a load size that matches the load being washed.
B
Brett KramerAug 28, 2025
Why are there dry spots on my Whirlpool 3LWTW4740 load after cycle?
- M
  Ms. Shirley EllisAug 28, 2025
  Dry spots on your load after a Whirlpool Washer cycle are normal. The high spin speeds combined with air flow during the final spin can cause items near the top of the load to develop dry spots.
J
Joyce ParkerAug 30, 2025
Why is my Whirlpool Washer load tangling?
- G
  Gina BushAug 31, 2025
  If your Whirlpool Washer load is tangling, ensure you're loading garments in loose heaps evenly around the basket wall. Mixing types of load items can help reduce tangling. Select a cycle with a slower wash action and spin speed, but be aware that items will be wetter. Use the recommended cycle for the type of garments being washed.
R
Rachel BishopSep 2, 2025
Why is my Whirlpool 3LWTW4740 not cleaning or removing stains?
- V
  Victoria SweeneySep 2, 2025
  If your Whirlpool Washer isn't cleaning or removing stains effectively, avoid tightly packing the load. Load garments in loose heaps evenly around the basket wall, and only add 1 or 2 additional garments after the washer has started. Add detergent, oxi products, and color-safe bleach to the bottom of the basket before adding the load items. Choose a load size that matches the load being washed.
S
steven00Sep 5, 2025
Why is my Whirlpool 3LWTW4740 having incorrect or wrong wash or rinse temperatures?
- R
  Ralph GarciaSep 5, 2025
  If your Whirlpool Washer has incorrect wash or rinse temperatures, check that the hot and cold inlet hoses are not reversed and are properly connected to both the washer and faucet, ensuring both hot and cold water are flowing. Also, check that the inlet valve screens are not clogged and that there are no kinks in the hoses. Note that this washer uses cooler wash and rinse water temperatures than older models, including cooler hot and warm washes, to save energy.
J
joseboydSep 8, 2025
What causes fabric damage in my Whirlpool 3LWTW4740?
- S
  Sylvia HernandezSep 8, 2025
  Fabric damage in your Whirlpool Washer can be caused by sharp items in pockets, tangled strings and straps, or pre-existing damage to items. Empty pockets, zip zippers, and tie all strings and straps before washing. Mend rips and broken threads before washing. Avoid tightly packing the load. Use a cycle designed for the fabrics being washed and do not add too many additional garments after the cycle has started. Do not pour liquid chlorine bleach directly onto the load and always follow garment care instructions.
J
Joanne FloresSep 12, 2025
Why is there sand, pet hair, or lint on my Whirlpool Washer load after washing?
- M
  martinezjulieSep 12, 2025
  If you find sand, pet hair, or lint on your Whirlpool Washer load after washing, it may require additional rinsing. Add an Extra Rinse to the selected cycle to help remove these residues.

Whirlpool 3LWTW4740 Specifications

General

Brand	Whirlpool
Model Number	3LWTW4740
Type	Top Load Washer
Color	White
Energy Star Certified	No
Number of Wash Cycles	12
Wash Action	Agitator
Delay Wash Option	No
Quick Wash Option	Yes
Built-In Water Heater	No
Voltage	120 V
Frequency	60 Hz
Width	27 in
Depth	27 in
Height	43 inches
Cycle Options	Bulky Items, Heavy Duty, Normal, Quick Wash, Rinse & Spin, Soak