What does 'rL' mean on my Whirlpool 7MWFW6621HC Washer display?
If the display shows “rL” (remove load), it means a load was detected in the drum during the Clean Washer with affresh® cycle. Remove any items from the washer drum and restart the Clean Washer with affresh® cycle.
What does F# E# error code mean on my Whirlpool Washer?
If the display shows “F# E# or F## E## code other than as described above”, it indicates a system error code. Try touching POWER once to clear the code, then again to restart the washer. If the code appears again, it is recommended to call for service. You can also try unplugging the washer for 30 seconds and then plugging it back in.
How to troubleshoot drain pump error on Whirlpool Washer?
If the display shows “F9” followed by “E1” or “F09” followed by “E01”, this indicates a drain pump system error. Check the plumbing to ensure the drain hose is correctly installed and doesn't extend more than 4 1/2" (114 mm) into the standpipe. Also, ensure the drain hose isn't kinked, pinched, or blocked, and remove any clogs. Use the drain hose form and securely attach it to the drainpipe or tub. Lower the drain hose if its end is higher than 96" (2.4 m). Finally, make sure you're using only HE detergent and measuring it according to the manufacturer's directions based on load size and soil level.
What to do if my Whirlpool 7MWFW6621HC displays a water supply error?
If the display shows “Lo” followed by “FL” or “F8” followed by “E1” or “Lo” followed by “FL” or “F08” followed by “E01”, it indicates a water supply error. The unit will drain for 8 minutes with the door locked, and this drain cycle must finish to reset the error code. Once done, press POWER once to clear the code, then again to restart the washer. If the code reappears, it is recommended to call for service. Also, ensure that both inlet hoses are properly attached and that water is flowing to the inlet valve, and both hot and cold water faucets are turned on. Check the inlet valve screens for clogs, remove any kinks in the inlet hose, and ensure auto shut-off connectors and hoses are correctly installed and functioning. Use only the manufacturer’s recommended inlet hoses.
What to do if “Sd” or “SUD” (excess suds) appears on my Whirlpool Washer?
If the Whirlpool Washer displays “Sd” or “SUD,” it means there are too many suds. The washer is trying to reduce them. Let the washer continue its cycle. Make sure you're only using HE detergent and follow the detergent manufacturer’s instructions to determine the correct amount based on your load size. If the issue continues, consider switching to a different HE detergent.
Why my Whirlpool 7MWFW6621HC won’t start or fill with water?
If your Whirlpool washer won’t run or fill, or it stops working, ensure both inlet hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Check the inlet valve screens for clogs and remove any kinks in the inlet hoses. Verify the power cord is plugged into a grounded 3-prong outlet, avoid using an extension cord or GFCI, and ensure the outlet has power. If problems persist, have an electrician check the voltage and reset any tripped circuit breakers or replace blown fuses.
How to stop my Whirlpool 7MWFW6621HC Washer from vibrating?
To resolve excessive vibration, rocking, or “walking” in your Whirlpool washer: * Ensure the front and rear feet are firmly in contact with the floor and locked, with the jam nuts tight against the cabinet bottom. * Check the floor for flexing or sagging. If uneven, use a 3/4" (19 mm) piece of plywood underneath the washer. Avoid raised wooden platforms. * Avoid tightly packed or excessively large loads, and balance single items like rugs with a few extra items. * Make sure you have removed the shipping bolts from the back of the washer.
Why won't the door lock on my Whirlpool 7MWFW6621HC Washer?
If the display shows “F5” followed by “E2” or “F05” followed by “E02”, it means the washer door isn't locking. Press POWER to cancel the cycle. Make sure the door is fully closed and latched, and check inside the drum for items that might be preventing the door from closing properly.
Critical safety guidelines to prevent hazards like fire, shock, and injury.
Explanation of buttons, display, and basic functions like power and cycle selection.
Guidance on selecting HE detergents and understanding concentration for optimal cleaning.
How to select cycles, adjust settings, start, pause, and manage the wash process.
Common error codes, their causes, and recommended solutions for display issues.
To Next Page
General
