Whirlpool cabrio W10560171B User Manual (English)

Questions and Answers:

L
lmckeeAug 13, 2025
Why is my Whirlpool Washer not draining or spinning properly?
- C
  caleb63Aug 13, 2025
  If your Whirlpool Washer isn't draining or spinning, loads are still wet, or the spin light is on, it means the washer couldn't pump out water in ten minutes. First, check that the drain hose is correctly installed, using the drain hose form and securing it to the drainpipe or tub, without taping over the drain opening. If the hose end is higher than 96" (2.4 m) above the floor, lower it. Also, clear any clogs from the drain hose. Another cause might be using the wrong detergent or too much of it, leading to excessive suds. Use only HE detergent, carefully measuring according to the load size. To get rid of extra suds, select RINSE & SPIN without adding any detergent.
V
valerie24Aug 16, 2025
How to dissolve single-dose laundry packet in Whirlpool cabrio W10560171B Washer?
- B
  Bobby WilliamsAug 17, 2025
  To ensure single-dose laundry packets dissolve correctly in your Whirlpool washer, always add the packet to the washer basket before adding clothes. Never put the packet in the dispensers. Follow the manufacturer’s instructions to avoid damage to your garments.
K
Karen HarrisAug 25, 2025
Why is my Whirlpool cabrio W10560171B Washer load not rinsing properly?
- A
  Aaron ChandlerAug 25, 2025
  If your Whirlpool washer load is not rinsed, several factors could be at play. Make sure that both the hot and cold inlet hoses are not reversed and that both are attached with water flowing to the inlet valve, ensuring both hot and cold water faucets are turned on. Also, check the inlet valve screens for any clogs and remove any kinks in the inlet hose. It's crucial to use only HE detergent and measure it correctly, as regular detergent can interfere with the washer's operation. Load garments loosely around the washplate, and select a cycle designed for the fabrics being washed, adding only 1 or 2 additional garments after the washer has started.
A
Andres BrandtAug 28, 2025
What to do if there is sand, pet hair, or lint on clothes after washing in my Whirlpool cabrio W10560171B?
- E
  Emily EllisAug 28, 2025
  If you find sand, pet hair, or lint on your clothes after washing in your Whirlpool washer, it may be due to heavy residues. Adding an extra rinse to the selected cycle can help remove these residues.
C
Corey CrawfordSep 1, 2025
How to prevent clothes from tangling in my Whirlpool cabrio W10560171B Washer?
- T
  tiffanyjohnsonSep 1, 2025
  If your Whirlpool washer is causing your load to tangle, ensure you are loading garments in loose heaps evenly around the washplate. Selecting a cycle with a slower wash action and spin speed can also help, though items will be wetter. Mix different types of items in the load and use the recommended cycle for the garments you are washing.
S
Sydney TorresSep 4, 2025
Why are the wash and rinse temperatures wrong on my Whirlpool cabrio W10560171B?
- H
  Heather RichardsSep 4, 2025
  If you're experiencing incorrect wash or rinse temperatures with your Whirlpool washer, start by checking that the hot and cold inlet hoses are not reversed and that the inlet valve screens are not clogged. Also, make sure there are no kinks in the hoses. Keep in mind that ENERGY STAR® qualified washers use cooler wash and rinse water temperatures than traditional top-load washers, including cooler hot and warm washes.
S
Sara OwensSep 8, 2025
Why are there dry spots on my clothes after a Whirlpool cabrio W10560171B Washer cycle?
- A
  Ashley BakerSep 8, 2025
  If you find dry spots on your load after a cycle in your Whirlpool washer, it is normal. The high spin speeds combined with air flow during the final spin can cause items near the top of the load to develop dry spots during the final spin.