Whirlpool W10661460B User Manual

Steps 3 & 4 apply only
to certain models
While holding the door,
remove 3 hex head screws
and the hinge pin.
DOOR SWING REVERSAL INSTRUCTIONS W10661460B (OPTIONAL)
Remove food and any adjustable bins from the doors.
IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.
When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions.
Lift freezer door from
the center hinge pin.
2
Center Hinge - Loosen the 2
screws (6 turns) on the left-
hand side and remove the
screw from the right-hand side.
3 4
Center Hinge - While holding the
door, loosen the 2 screws on the
right-hand side and remove the
screw from the left-hand side.
5
Remove Freezer
and Refrigerator
Doors
NOTE: After removing the
doors, place them on a soft
surface to avoid damaging
the finish.
Move the door stop, located on the bottom of the door,
to the opposite side.
A. Door Stop Screw B. Door Stop
Move the door stop, located on the bottom of the door,
to the opposite side.
A. Door Stop Screw B. Door Stop
Move the 3 cabinet hole
plugs to the opposite side.
1
Reverse Door Stops
Freezer
Door
Refrigerator
Door
Install Doors
Freezer
Door
Refrigerator
Door
Align
Doors
1
Completely tighten the
3 Top Hinge screws.
2
Move the base grille cover
to the opposite side.
3
Reinstall the base grille.
4
Tighten the two screws (previously
loosened), and reinstall and
tighten the Center Hinge screw.
Tools Required
 " Hex head socket wrench
 " Open-end wrench
 Phillips screwdriver
 ¼" Hex key
 Flat 2" putty knife
Reversibility Kit
(a) Removal tool
(b) Brand badge
(c) Instructions
(d) Hole plug
(e) Two screws
5
16
/
5
16
/
(a) (b)
(c)
(d)
(e)
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
5
W10661460B
© 2014 Whirlpool Corporation.
All rights reserved.
6/14
Printed in Mexico
Open doors left to right. Open doors right to left.
1
Insert the 3 Top Hinge screws
so they are halfway into the
Top Hinge and the top of
the cabinet.
2
Set the freezer door
onto the Center Hinge.
3
A
B
A
B
1
1
Brand
Badge
Lift refrigerator door from bottom
hinge. NOTE: The hinge style will
vary depending on the model.
6
or
For models with base grilles,
firmly pull the grille
toward you to remove.
Move the bottom hinge to the opposite side
of the cabinet. Make sure the washer remains
on the hinge pin. NOTE: The hinge style
will vary depending on the model.
1
or
Set the refrigerator door onto
the bottom hinge pin.
2 3
Tighten the screws (previously loosened),
and reinstall and tighten the Center Hinge screw.
NOTE: Make sure washers are on both the top
and bottom pins of the center hinge.
1
8
/
Align the Freezer and Refrigerator
doors. NOTE: Make sure to allow a
¾" (19 mm) gap between the doors.
¾"
(19 mm)

Whirlpool W10661460B Specifications

General

Category	Refrigerator
Brand	Whirlpool
Model Number	W10661460B
Refrigerator Style	Top Freezer
Total Capacity	18.2 cu. ft.
Color	Black
Energy Star Certified	Yes
Defrost Type	Frost-Free
Number of Shelves	3
Number of Door Bins	4
Ice Maker	No
Reversible Door	Yes
Type	Top Freezer Refrigerator

Summary

Remove Freezer and Refrigerator Doors

Detach Freezer Door

Lift the freezer door from the center hinge pin after removing screws and hinge pin.

Detach Refrigerator Door

Lift the refrigerator door from the bottom hinge after loosening screws.

Loosen Center Hinge Screws

Loosen screws on the center hinge for the refrigerator door to prepare for removal.

Remove Base Grilles

For models with base grilles, firmly pull the grille toward you to remove it.

Reverse Door Stops

Move Freezer Door Stop

Relocate the door stop and its screw to the opposite side of the freezer door.

Move Refrigerator Door Stop

Relocate the door stop and its screw to the opposite side of the refrigerator door.

Install Doors

Relocate Bottom Hinge

Move the bottom hinge to the opposite side of the cabinet, ensuring the washer remains on the pin.

Mount Refrigerator Door

Place the refrigerator door onto the bottom hinge pin.

Mount Freezer Door

Set the freezer door onto the center hinge.

Secure Top Hinge

Insert top hinge screws halfway, then completely tighten them.

Align Doors and Finish

Position Door Plugs

Move the three cabinet hole plugs to the opposite side.

Adjust Door Spacing

Align doors, maintaining a 3/4" (19 mm) gap between them.

Reinstall Base Grille Cover

Move the base grille cover to the opposite side and reinstall the base grille.

Safety Warnings and Tools

Excessive Weight Hazard Warning

Use two or more people to move and install the refrigerator to prevent injury.

Required Tools

Lists necessary tools such as socket wrenches, screwdrivers, and putty knife.

Reversibility Kit Contents

Details items included in the door swing reversal kit, such as badges, tools, and screws.