Note:! This% equipment% has% been% tested% and% found% to% comply% with% the% limits% for% a% Class% B%
digital%device,%pursuant% to%part%15%of%the%FCC% Rules.%% These%limits%are%designed%to%provide%
reasonable% protection% against% harmful% interference% in% a% residential% installation.% % This%
equipment%generates,%uses%and%can%radiate%radio%frequency%energy%and,%if%not%installed% and%
used% in% accordance% with% the% instructions% may% cause% harmful% interference% to% radio%
communications.% % However,% there% is% no% guarantee% that% interference% to% will% not% occur% in% a%
particular% installation.% % If% this% equipment% does% cause% harmful% interference% to% radio% or%
television% reception,% which% can% be% determined% by% turning% the% equipment% off% and% on,% the%
user% is% encouraged% to% try% to% correct% the% interference% by% one% or% more% of% the% following%
measures:%
Reorient%o r%relocate%the%rec eiving %antenna.%Increase%t he %separation%between%th e%equipment%
and%receiver.%%Connect%the%equipment%into%an%outlet%on%a%circuit%different%from%that%to%which%
the% receiver% is% connected.% % Consult% the% dealer% or% an% experienced% radio/TV% technician% for%
help.%%Install%an%approved%low%pass%filter.%
Modifications%not%expressly%approved%by%the%manufacturer%could%void%the%user’s%authority%to%
operate%the%equipment%under%FCC%rules.%
%
Wi3%Patents%#6,108,331%and%#7,027,431%apply.%
%
%
%
%
%
%
Wi3%Pub.%WiP7001p.OSGv1.4
1. Connect%WiP7001p%to%Computer%using%Ethernet%patch%cord.%
2. Set%computer%TCP/IP%properties%to%Static!IP!192.168.144.100%in%
the% IP% address% field% and% 255.255.255.0% in% the% Subnet% Mask%
field.%%Click%on%Submit%or%Apply%button%to%activate%change.%
3. Open% Internet% browser% on% computer% and% enter% the% Static%IP%
Address%assigned%to%the%WiP7001p%into%browser%address%bar.%
4. Enter%the%User%Name%“admin”%and%Password%“wi3admin”%
5. Select%“PHY%Rate”%in%left%most %column%
6. When% complete,% reset% computer% TCP/IP% back% to% original%
The%PHY%Rate%table%shows%
the%actual%PHY%rates%
between%each%of%the%
MoCA%devices%within%the%
coax%network.%%Each%
MoCA%device%is%identified%
by%the%last%six%digits%of%its%
Mac%Address.%
Target%network%data%rates%
for%MoCA1.1%devices%are%
200%Mbps%and%above.%%
Target%network%data%rates%
for%the%MoCA2.0%devices%
are%600Mbps%and%above.%
Lower%data%rates%are%
often%indicative%of%cable%
infrastructure%issues%such%
as:%Cable%lengths%greater%
than%300ft%between%
MoCA%devices,%poor%
quality%F%connectors,%low%
quality%splitters%and/or%
damaged%coax%cables%
• One%WiP7001p%Ethernet%Coax%Bridge%
•
One%External%Power%Adapter%–%DC%12v/1A%
To Previous Page
Loading...
Need help?
General