Wi3 WiP7001p User Manual

!
Computer!Setup!for!Switching!to!Static!IP!
!
Windows10!Computers!!
1. Go%to%Settings>Network%&%Internet>Local%Area%Connection>Properties%
2. Select%Internet%Protocol%Version%4%(TC/ IPv4)%then%select%Properties%
3. Select%”Use%the%following%IP%Address”%%
4. Enter%IP%Address:%192.168.144.100%
5. Enter%Submask:%255.255.255.0%
6. Select%“OK”%
7. Open%internet%browser%
8. Enter%default%IP%Address%of%the%WiP7001p%–%192.168.144.20%
9. When%complete,%reset%computer%to%original%TC/IP%settings%
%
MacOS!Computer!Settings!
1. Go%to%System%Preferences>Network%
2. Select%“Ethernet”%in%left%column%list.%
3. Change%Configure%IPv4%from%“DHCP”%to%“Manually”%
4. Enter%IP%Address:%192.168.144.100%
5. Enter%Submask:%255.255.255.0%
6. Select%“Apply”%
7. Open%internet%browser%
8. Enter%default%IP%Address%of%the%WiP7001p%–%192.168.144.20%
9. When%complete,%reset%computer%to%original%TC/IP%settings%
Note:%WiP7001p%is%not%compatible%with%Satellite%TV%systems.%%%
!"#$%&'(#)"**")$+(&,)-.#&
The$WiP7001p$Ethernet$Bridges$may$be$installed$without$any$configuration$or$setup$by$
simply$connecting$to$the$coax$network$as$shown$in$the$Connection$diagram.$
1. Check$coax$endp oint$location$connections$to$confirm$that$they$are$connected$to$the$
main$coax$TV$network.$
2. Locate$the$Broadband$Modem.$
3. Make$connections$as$shown$in$the$system$installatio n$ overview.$
4. If$existing$cabling$system$has$an$RF$amplifier,$it$must$be$replaced$by$a$MoCA$B yPass$
Amplifier$$
5. If$Cable$STB’s$are$MoCA$devices,$a$2-way$MoCA$splitter$must$be$used$to$allow$MoCA$
signal$to$pass$to$STB$(WiP7001p$does$not$pass$MoCA$through$TV$Only$F$connector)$
6. Install$additional$WiP7001p’s$or$WIP7500$WIFI$AP’s$in$any$desired$room$that$has$an$
active$Coax$cable$connection$home$run$to$the$MoCA$splitter.$
/01"(%-0&2+(3$456")$+(&7&'(#)"**")$+(&,)-.#&
The$WiP7001p$can$be$configured$t o$allow$custom$settings$such$as:$$assignment$of$a$static$
IP$Address,$upgrade$of$Firmware$and$access$to$a$built-in$network$PHY$rate$table$for$
diagnostics$and/or$verification$of$physical$cabling$integrity.$$Steps$to$access$the$
configuration$setup$are$as$follows:$
1. WiP7001p$must$not$be$connected$to$coax$network$during$this$procedure.$
2. Connect$computer$directly$to$the$WiP7001p$with$an$Ethernet$cable.$
3. Set$computer$TCP/IP$properties$setting$to$a$static$IP$Address$which$is$on$the$same$
subnet$as$the$WiP7001p ’s$default$IP$Address$–$89:;8<=;8>>;8??.$$Also$set$the$
Subnet$Mask$to$:@@;:@@;:@@;?.$
4. Open$Web$browser$on$the$computer$and$enter$the$WiP7001p$default$static$IP$
Address$of$89:;8<=;8>>;:?$into$the$browser$address$bar.$
5. Enter$the$User$Name$“admin”$and$ Password$“wi3admin”.$
6. Select$desired$menu$item$on$the$setup$page.$
7. When$complete,$reset$computer$to$original$TCP/IP$network$settings.$
System!Installation!Overview

Wi3 WiP7001p Specifications

General

Wi-Fi Bands	2.4 GHz
Ports	4 x RJ45 LAN ports
Wireless Standards	IEEE 802.11b/g/n
Maximum Data Rate	300Mbps
Security	WPA, WPA2

Summary

System Installation Overview

Basic Installation Steps

Steps for basic connection and setup of the WiP7001p Ethernet Bridges.

Advanced Configuration & Installation Steps

Steps for custom settings like static IP, firmware upgrades, and diagnostics.

Computer Setup for Switching to Static IP

Guide for setting a static IP address for Windows 10 computers.

MacOS Computer Settings

Guide for setting a static IP address for MacOS computers.

Coax Network PHY Test

PHY Rate Table

Displays actual PHY rates between MoCA devices, indicating potential infrastructure issues.

FCC Compliance and Interference Notes

Information on FCC compliance, potential interference, and user correction measures.