24
EN
INSTRUCTION MANUAL · HEAT PUMP
HEALTH MODE / SCAVENGING function
Press this button to turn on or turn off the health and scavenging functions in
operation status. Press this button for the rst time to start scaveng- ing function;
LCD displays SCAVENGING icon. Press the button for the second time to start
health and scavenging functions; LCD displays SCAVENGING icon and HEALTH
icon. Press this button for the third time to quit health and scavenging functions
simultaneously. Press the button for the fourth time to start health function; LCD
display HEALTH icon. Press this button again to repeat the operation above.
Note:
The function is only available for some models.
LIGHT button
Press this button to turn on or turn off the display light on the indoor unit.
The display light is defaulted on after energization.
TEMP button
Press this button, you can see indoor set temperature, indoor ambient
temperature on indoor unit’ s display.
Energy-saving function
Under cooling mode, press “TEMP” and “CLOCK” buttons simultaneously
to start up or turn off energy-saving function. When energy-saving function is
started up, “SE” will be shown on remote controller, and air conditioner will
adjust the set temperature automatically according to ex-factory setting to
reach to the best energy-saving effect. Press “TEMP” and “CLOCK” buttons
simultaneously again to exit energy-saving function.
Note:
• Under energy-saving function, fan speed is defaulted at auto speed and it
can’t be adjusted.
• Under energy-saving function, set temperature can ‘t be adjusted. Press
“TURBO” button and the remote controller won’t send signal.
• Sleep function and energy-saving function can ‘t operate at the same time.
If energy-saving function has been set under cool mode, press 11SLEEP11
button will cancel energy-saving function. If sleep function has been set under
cool mode, start up the energy-saving function will cancel sleep function.
Under off status, press
11MODE11
and
11
WiFi
11
buttons
simultaneously for 1s, WiFi module will restore
factory settings.
Press this button to turn on or turn off the health
and scavenging functions in operation status.
Press this button for the first time to start scaveng-
ing function; LCD displays
11 11.
Press the button
for the second time to start health and scaveng-
ing functions; LCD displays
11
11
and
11
11.
Press
this button for the third time to quit health and
scavenging functions simultaneously. Press the
button for the fourth time to start health function;
LCD display
11
11.
Press this button again to
repeat the operation above.
8
C
heating
function
Under heat mode, press 11TEMP11 and 11CLOCK11
buttons simultaneously to start up or turn off 8
C
heating function. When this function is started up,
Press this button to turn on or turn off the display
light on the indoor unit.
The display light is defaulted on after energization.
Press this button, you can see indoor set tempera-
ture, indoor ambient temperature on indoor unit' s
display. The setting on remote controller is select- ed
circularly as below:
Press
11
11
and
11
11
simultaneously to turn on or
turn off child lock function. When child lock func-
tion
is on,
11
11
icon is displayed on remote control-
ler.
If you operate the remote controller, the
11
11
icon
will blink three times without sending signal to the
unit.
Under OFF status, press
11
11
and 11MODE11 buttons
simultaneously to switch temperature display
between
C
and
F
.
LIGHT
Child lock function
be adjusted. Press 11TURBO11 button and the remote
been set under cool mode, press 11SLEEP11 button will
adjusted. Press 11TURBO11 button and the remote
Sleep function and 8C heating function can
't operate
at the same time. If 8C heating function has been set
under heat mode, press 11SLEEP11 button will cancel 8C
heating function. If sleep function has been set under
TEMP
Energy-saving function
Temperature display switchover function
no display
To Next Page
Loading...
