EasyManuals Logo

Winco 25PTOC-3/F User Manual

Winco 25PTOC-3/F
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
READ
ALL INSTRUCTIONS CAREFULLY BEFORE AlTEMPTlNG TO INSTALL, OPERATE OR SERVICE
THE
GENERATOR. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY IN-
FORMATION. FAILURE TO COMPLY
WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE!
RETAIN
INSTRUCTlONS
FOR
FUTURE REFERENCE.
Description
7.
This generator must be properly grounded.
These rotating armature power take-off generators
are designed primarily for farm use as a standby
electrical power supply, utilizing the power take-off
of a tractor or truck as the prime mover. The portable
trailer-mounted unit can be used to provide electri-
cal power to machinery and out-buildings where
commercial power is not accessible.
NOTE: The prime mover which drives the generator
must be capable of delivering approximately2.2 H.P.
per 1000 watts output from the generator.
Unpacking
NOTE: DO NOT invert generator during unpacking.
Gearcase contains oil.
Unpack the generator as follows:
1. Remove strapping from carton.
2.
Lift off carton.
3. Remove the small
subpack carton.
4.
Open the subpack carton; it contains:
a.
One generator instruction manual
b.
One load disconnect plug (disassambled, in
bag). for
25PTOC-8JF One range/welding
plug, for
CSABPTOC-3IC
c.
One quality control inspection tag.
5. Remove the four bolts which hold down the gen-
erator feet to the pallet. (A six inch crescent
wrench is suitable for this job.)
6.
Lift the generator from the pallet by means of the
lifting eye on the top of the generator.
7.
Inspect the generator for freight loss or damage.
Genera Safety Information
1.
Do not allow anyone to operate the generator
without,proper instruction.
2.
Guard against electric shock.
3. Avoid touching live terminals or receptacles.
4.
Be extremely careful
if
operating this generator
in rain or snow.
5. Do not make or break electrical receptacle con-
nections under
.load.
6.
Use only grounded receptacles and extension
cords.
8. Hot engine parts, moving partsi aid generator
output all can seriously injure the generator
operator. The operator must use caution and
remain alert when using this generator.
9. Provide safety guards for all drive systems.
10. Keep all safety guards and power shields in po-
sition and tightly secured.
11. When operating this generator. do not wear
neckties, loose articles of clothing, or anything
else that can be caught in moving parts.
12. Engine exhaust fumes are poisonous. Do not
inhale them. Provide adequate ventilation if
prime mover for generator is gas or diesel en-
gine. Be sure generator itself is well ventilated.
13. The generator manufacturer recommends that
only qualified electrical technicians be allowed
to service (install, maintain. repair, or replace
parts) this generator, and that only factory ap-
proved repair parts be used in it.
14. Do not work on this generator when fatigued.
15. Use extreme caution when working on electrical
components. High generator output can cause
injury or death.
16. Installing and wiring a home-standby generator
installation is not a "do it yourself" project.
Consult
a
qualified, licensed electrician or con-
tractor. The installation must comply with all
national, state, and local codes.
17. Excessive noise is tiring, and continual expo-
sure to it can cause some degree of temporary
and permanent hearing loss. Muffle engine
noise with the best available noise suppression
equipment; wear noise protection devices when
necessary.
18. Keep the generator and the area around it clean.
Remove all material that can create slippery
conditions, such as grease, water, ice, and
snow. Also remove oily rags and other flamma-
ble material from the area.
19. Keep a fire extinguisher near the generator. Ex-
tinguishers rated ABC by the NFPA are appro-
priate for this use. Consult the local fire depart-
ment if you have questions regarding fire extin-
guisher ratings. Keep the extinguisher properly
maintained and be familiar with its proper use.
Specifications
GEN.RPM
3600
3600
INS.
B
F
PH
1
1
HZ.
60
60
INPUTRPM
540
540
AMPS
66/33
208/104
VOLTS
1201240
120/240
MODEL
-
8PTOC
25PTOC
WATTS
8000
25000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Winco 25PTOC-3/F and is the answer not in the manual?

Winco 25PTOC-3/F Specifications

General IconGeneral
Model25PTOC-3/F
Fuel TypeGasoline
PhaseSingle
Frequency60 Hz
Weight435 lbs
Engine Type4-Stroke OHV
Starting SystemRecoil Start
Max AC Output2500 Watts
AC Output120V/240V
Voltage120/240V
Starting MethodRecoil
Dimensions20.5 x 17.5 x 17.5 inches
Engine4-Stroke OHV
Engine Displacement79.7 cc
DC Output12V DC
Noise Level68 dB

Related product manuals