Electronics and Gas Theory
Integrated Modules
Integrated Modules
2-15
#826498 - Revision B - December, 2016
f. Error Code Indicator - CE152TF/S, CI152TF/S and TM15TF/S
Touch “+” pad during the Coil Temperature test. 1.
CE152TF/S and CI152TF/S - six “.” are displayed on rear control zone.•
TM15TF/S - six “.” are displayed on front control zone.•
CE152TF/S and CI152TF/S - front control zone shows 0-8 dimmed “.” based on how many error codes•
are logged.
TM15TF/S - rear control zone shows 0-8 dimmed “.” based on how many error codes are logged.•
Fully lit LED indicates which error is being displayed in the 2-digit display. •
If only a single error has been logged, only a single fully lit LED is displayed. •
If no errors logged SIM/MLT/LO, HI, and “.” are not displayed and “- -” is displayed in the 2-digit display. •
2-digit display shows the corresponding error code stored in memory. •
Rear SIM/MLT/LO and HI are dimmed. A touch of the front control zone SIM/MLT/LO or HI pads cycles2.
through the stored error codes.
Touch and hold TIMER pad for 5 seconds to clear error code history. 3.
Clearing the error code history is only possible if at least one error was logged. •
Clearing the error code history is confirmed by a double beep. •
If an error is currently present when the log is cleared, it immediately regenerates an error code. •
“-” pad returns to Coil Temperature test and “+” pad advances to Showroom Mode menu.4.
f. Error Code Indicator - SM15TF/S, FM15TF/S and GM15TF/S
Touch “+” pad during the RTD Temperature test. 1.
Five “.” are displayed on rear control zone.•
Front control zone shows 0-8 dimmed “.” based on how many error codes are logged•
Fully lit LED indicates which error is being displayed in the 2-digit display. •
If only a single error has been logged, only a single fully lit LED is displayed. •
If no errors logged LO, and HI, and “.” are not displayed and “- -” is displayed in the 2-digit display. •
2-digit display shows the corresponding error code stored in memory. •
A touch of the front control zone LO or HI pads cycles through the stored error codes. 2.
Touch and hold TIMER pad for 5 seconds to clear error code history. 3.
Clearing the error code history is only possible if at least one error was logged. •
Clearing the error code history is confirmed by a double beep. •
If an error is currently present when the log is cleared, it immediately regenerates an error code. •
“-” pad returns to RTD Temperature test and “+” pad advances to Showroom Mode menu4.
g. Showroom Mode - CE152TF/S, CI152TF/S, and TM15TF/S
Touch “+” pad during the Error Code Indicator. 1.
CE152TF/S and CI152TF/S - Seven “.” displayed on rear control zone.•
TM15TF/S - Seven “.” displayed on front control zone.•
To engage showroom mode.2.
CE152TF/S and CI152TF/S - touch the front control zone HI pad to engage showroom mode.•
TM15TF/S - touch the rear control zone HI pad to engage showroom mode.•
SH is displayed in the 2-digit display when in showroom mode.•
To disengage showroom mode.3.
CE152TF/S and CI152TF/S - touch the front control zone SIM/MLT pad. •
TM15TF/S - touch the rear control zone LO pad.•
”-” pad returns to Error Code indicator and “+” pad advances to Software Version indicator.4.
g. Showroom Mode - SM15TF/S, FM15TF/S, GM15TF/S
Touch “+” pad during the Error Code Indicator. 1.
Six “.” displayed on rear control zone.•
To engage showroom mode.2.
Touch the front control zone HI pad to engage showroom mode.•
SH is displayed in the 2-digit display when in showroom mode.•
To disengage showroom mode.3.
Touch the front control zone LO pad. •
”-” pad returns to Error Code indicator and “+” pad advances to Software Version indicator.4.
To Next Page
Loading...
