To Next PageTo Next Page
Need help?Do you have a question about the Woodbridge T-0737 and is the answer not in the manual?
Emphasizes reading all instructions before handling the product to prevent injury.
Provides detailed measurements and diagrams of the toilet's physical specifications.
Crucial first step to shut off water supply before starting any installation.
Guides on positioning and setting the new toilet bowl for a watertight seal.
Instructions for connecting the water supply line to the toilet tank.
General safety precautions and instructions for using the bidet seat.
Mandatory safety warnings and precautions before operating the bidet seat.
Critical warnings to prevent electrocution hazards associated with the bidet seat.
Essential safety guidelines for product installation and usage, including electrical safety.
Detailed instructions on proper grounding to prevent electrical shock.
Step-by-step guide for installing the mounting plate onto the toilet.
Detailed steps for connecting the water supply to the unit.
Guides on connecting power and water, and performing self-inspection checks.
Lists common issues with flushing, temperature, and operation with their respective solutions.
Important cautions regarding product malfunctions and electrical issues.
This document provides installation and care instructions for a WOODBRIDGE® toilet and bidet seat combination. It emphasizes safety precautions, proper installation procedures, and maintenance guidelines to ensure the product's longevity and safe operation.
The toilet is designed for residential use and is certified to meet various plumbing codes and standards, including the 2015 Uniform Plumbing Code (UPC), 2018 International Plumbing Code (IPC), and WaterSense® certification for water efficiency. It also complies with CSA B45.5 / IAPMO Z124-2017 for plastic plumbing fixtures.
The installation process begins with preparing the closet flange, which involves removing the old toilet, cleaning the area, and ensuring the rough-in measurement is 12 inches from the wall to the center of the closet flange. The document stresses the importance of shutting off the main water supply before starting any work. Two people are required to lift and install the toilet due to its weight and ceramic fragility.
Once the flange is ready, a wax ring is installed over the horn discharge at the bottom of the new toilet bowl. The toilet is then carefully placed over the closet flange, aligning the bolts with the holes in the toilet's base. The installer must press down with a slight twisting motion to evenly compress the wax ring and create a watertight seal, ensuring the bowl is level. Rocking the toilet back and forth is explicitly warned against, as it can break the seal. After the toilet is set, washers and nuts are installed over the closet bolts and tightened, but not overtightened, to avoid damaging the ceramic base. The document notes that due to the skirted trap-way design, installation may require more patience and accessibility.
Connecting the toilet's tank to the water supply line involves using a toilet hose (not supplied) to link the tank to the water shut-off valve. The coupling nut should be tightened by a quarter turn beyond hand-tight, with a warning against overtightening to prevent leakage. After connecting, the water supply valve is turned on to fill the tank, and all connections are checked for leaks. The toilet should be flushed 4-5 times to test the flushing system and ensure the wax ring is properly sealed. If shims are used, they should be trimmed, and silicone sealant should be applied around the base of the toilet, allowing 24 hours to dry before use. The manual emphasizes checking for leaks regularly during the first day and week after installation.
The bidet seat installation involves mounting the base plate and connecting the water supply. First, expansion nuts are pressed into the toilet's installation holes. The base plate, plastic plates, flat washers, and bolts are then installed and tightened according to the provided diagram. An installation paperboard is used to align the base plate with the ceramic bowl.
For connecting the water supply, two options are provided: side inlet and bottom inlet. For a side inlet, a 3-way valve is installed onto the angle valve, and then the water supply hose and washlet inlet hose are attached to the 3-way valve. The L-shaped end of the water supply hose connects to the washlet inlet connector. For a bottom inlet, the water supply connects directly to the inlet connector, and the supply hose and power line are routed through the relevant holes before installing the seat cover. The manual warns against distorting or damaging the supply hose and advises against using old or non-brand water supply hoses and accessories.
After physical installation, the power and water supply are checked. The water supply hose is connected, and the angle valve is turned on, checking for leaks. The power plug is inserted into a grounded power socket. If an electric leakage protection plug is used, the protection switch should be pressed, and the indicator light should turn on. Before usage, the electric leakage test button should be pressed to ensure the protection function works. The main unit buzzer will ring "click" twice, indicating self-inspection is complete. The water tank will then fill, and heating will take approximately 3 minutes.
The bidet seat offers several functions controlled by keys on the main unit and an actuator.
The bidet seat also provides visual indicators: in functional mode, the power light is on, and the energy saver light is off. In energy save function, the power light is off, and the energy saver light is on. In standby mode, both lights are off. All functions default to a middle level, which can be adjusted using the remote control. If the product is not used for 72 consecutive hours, the water in the tank automatically discharges for 90 seconds and is replaced with fresh water to prevent bacteria growth.
Regular maintenance is crucial for the toilet and bidet seat.
The document advises using soft sponges or cloths for cleaning and rinsing thoroughly immediately after using any cleaning solutions. Abrasive cleaners (acid, ammonia, bleach, etc.) and abrasive sponges or cloths (steel wool, wired brushes) are strictly prohibited, as they can cause corrosion, finish peeling, dullness, and permanent scratches. For fill/flush valves, no chlorine or other chemicals should be poured into the tank, as this can damage components and void the warranty. The fill and flush valves are designed to be maintenance-free.
A troubleshooting guide is included to address common issues:
The manual emphasizes retaining these instructions for future reference and provides customer service contact information.
General| Product Type | Toilet |
|---|---|
| Model Number | T-0737 |
| Flush Type | Dual Flush |
| Flush Volume (Full) | 1.6 GPF |
| Rough-In Size | 12 inches |
| Bowl Shape | Elongated |
| Material | Vitreous China |
| Color | White |
| ADA Compliant | Yes |
| WaterSense Certified | Yes |
| Installation Type | Floor Mounted |
| Flush Volume (Reduced) | 1.0 GPF |
| Seat Height | Comfort Height (16.5 inches) |
