Woodstock SHOP FOX W1758 User Manual (English)

Questions and Answers:

J
Jaime WeissAug 14, 2025
Why is my Woodstock Lathe vibrating so much?
- L
  Laura WalkerAug 15, 2025
  If your Woodstock Lathe experiences excessive vibration, several factors could be at play. It may be due to incorrect mounting of the workpiece, or the workpiece itself might be warped, out of round, or flawed. The spindle speed might be too high for the mounted workpiece. Ensure the lathe rests on an even surface by shimming the legs or adjusting the machine feet. Check and tighten the motor mounting bolts if they are loose. A worn or damaged V-belt can also cause this issue, and should be replaced. Lastly, worn spindle bearings can contribute to excessive vibration, and should be replaced.
M
Michelle LynchAug 17, 2025
What to do if my Woodstock SHOP FOX W1758 Lathe will not start?
- M
  Meredith ChavezAug 17, 2025
  If your Woodstock Lathe won't start or growls upon startup, the issue could stem from several causes. First, check if the power supply fuse or circuit breaker has tripped, and if so, inspect the circuit for shorts and replace the breaker if necessary. The motor fan cover might be dented, preventing the fan from spinning, in which case you should replace or adjust the fan cover and inspect the motor fan. A broken or faulty paddle switch could also be the culprit; use an ohmmeter to check the switch terminals for continuity and replace the switch if needed. Alternatively, the start capacitor or the motor itself may be at fault and require replacement.
D
davisdaleAug 21, 2025
How to fix vibration noise that changes with speed on my Woodstock SHOP FOX W1758 Lathe?
- K
  Kevin MartinAug 21, 2025
  If you're experiencing vibration noise from your Woodstock Lathe that changes when the speed is adjusted, it might be due to a loose V-belt cover. Try tightening the four screws securing it. If that doesn't resolve the issue, consider installing a soft, vibration-dampening material between the V-belt cover and the headstock. Another possibility is that the V-belt cover is bent or dented, making contact with the motor pulley or V-belt. Remove the V-belt cover and inspect it for any damage. Tap out any dents with a rubber mallet, bend it back into shape, or shim it away from the motor pulley. Finally, bad spindle bearings could also be the cause, requiring replacement.
C
carlaallisonAug 25, 2025
Why does my Woodstock SHOP FOX W1758 Lathe keep tripping the circuit breaker?
- S
  stephenblackAug 25, 2025
  If your Woodstock Lathe keeps tripping fuses or circuit breakers, there are a few potential causes to investigate. Start by inspecting the line cord or plug for damaged insulation and shorted wires, replacing the extension cord if necessary. A short circuit in the motor or loose connections could also be the problem. Finally, ensure that you have the correct fuses or circuit breakers installed in the power supply.
J
joseph70Aug 27, 2025
How to improve surface finish on my Woodstock Lathe?
- M
  Matthew WashingtonAug 27, 2025
  If your Woodstock Lathe is producing a bad surface finish, consider adjusting the spindle speed through trial and error to find a better setting. Additionally, ensure that you are using a sharp chisel or the correct chisel for the operation.
K
Kimberly GuzmanAug 31, 2025
What causes constant vibration noise on my Woodstock SHOP FOX W1758 Lathe?
- J
  Janet DavisAug 31, 2025
  If your Woodstock Lathe is experiencing vibration noise that remains constant regardless of speed changes, it may be due to a dented motor fan cover. Consider replacing or adjusting the fan cover, and inspect the motor fan for damage, replacing it if necessary. Another potential cause is bad spindle bearings, which would need to be replaced.
K
Kathryn SmallSep 3, 2025
Why do chisels grab on my Woodstock Lathe?
- B
  brooke88Sep 3, 2025
  If you find that chisels on your Woodstock Lathe grab or dig into the workpiece, it could be due to a few reasons. The tool rest might be adjusted too low, so try raising it. Alternatively, the tool rest might be set too far from the workpiece, so move it closer. Ensure you are using the correct chisel or tool for the job. Finally, check if the chisel or tool is dull; if so, sharpen or replace it.
S
Susan SmithSep 6, 2025
Why is the tailstock moving on my Woodstock SHOP FOX W1758?
- V
  Valerie MendozaSep 7, 2025
  If the tailstock on your Woodstock Lathe moves, it could be due to a loose tailstock mounting bolt, which you should tighten. Another possibility is that the bed surface is oily or greasy, so clean the bed surface to remove any excess oil or grease.
H
harrisrebeccaSep 10, 2025
How to remove a tapered tool stuck in my Woodstock SHOP FOX W1758's tailstock?
- L
  Lauren BrownSep 10, 2025
  If you cannot remove a tapered tool from the tailstock barrel of your Woodstock Lathe, ensure the tailstock quill is fully retracted into the tailstock by turning the quill handwheel until it forces the tapered tool out. Also, always make sure the mating surfaces of the quill and tapered tool are free from debris and oily substances before installing.

Woodstock SHOP FOX W1758 Specifications

General

Type	Wood Lathe
Swing Over Bed	16-1/2 inches
Distance Between Centers	46 inches
Motor Power	2 HP
Weight	215 lbs
Spindle Taper	MT#2
Tailstock Taper	MT#2
Voltage	110V
Spindle Bore	3/8 inches