Xcortech X3300W - X3300 CC Setup Operation; Flash Control (FLM); Boss Role (boSS); Count Down Setting (cnt)

Mode Selector select to ST (Setup Mode)
That can be setup below function (reference above flowchart for setup)
● FLM (flash control) : on/oFF, Setup Tracer BB on/oFF
● Boss : Team Battle Mode to limit team for BB counts
Link: http://youtu.be/leCexUHqET0
● cnt (count): 5-9999, Preset initial count down value
● WArn (warn): 1-100 & oFF, low ammo warning
(When low ammo warning, display will flash in count down mode)
● AEG.b (AEG battery): Display AEG’s battery voltage
(need to link with X3300SCU)
● Unit: M/F, Set unit for speed (meter/sec , feet/sec)
● APo (auto power off): 1-80 mins, Set auto power off
● Eco (save display power): on/oFF, auto adjust the screen brightness to
maximize battery life
● ttS (total shot count): 0-65000, Display total count, push and hold the “Data
Wheel” 3 sec to reset count.
● ScU (Shot Control Unit): Set burst round shot
(see Ch5 )
● rSt (reset): Reset to factory setting
CH-4. X3300CC Setup operation
※Need to connect X3300SCU (optional)
● b.rnd : oFF & 2-10 : Burst fire setting 2-10.
● b.tyP : 5.0-9.0 Voltage & oFF : Set low power level. The AEG will vibrate and
shutdown when lower battery level is detected.
Select oFF to disable this function.
● MEM : 1-8 : Set burst control channel, each channel includes the following factors:
cnt value
Warn value
b.rnd number
b.tyP select
bind information
● bind : Binding/paring with X3300SCU
● Exit : Exit
SCU setting Video: http://youtu.be/BJZ32J4UbQA
The Xcortech product information : http://goo.gl/W11LOK
CH-5. ＊X3300W ScU (shot control unit) setup
ScU
Burst Round
b.rnd
Adjust from
oFF, 2 ~ 10
Select battery type to active
low battery protect
b.tyP
Bind a EGATE
bind
Exit to upper layer
EXit
Select memory slot
MEM
Select slot from
1 ~ 8
Bind a ScU to
selected memory slot
5.0-9.0V Adjustable
oFF (Stop portect)
Low power
Warning and
shutdown level
Binding X3300W and X3300SCU
V1.17
Flash control
FLM
Speed Unit
Unit
M: Meter
F : Feet
Auto Power Off
APo
Adjust from 1 to 80
minute
Down count initial value
cnt
Low ammo warning level
WArn
Adjust from 5 to 9999
Adjust from 1 to 100
0 means warning oFF
Save Display Power
Eco
on
oFF
Shot control unit
ScU
Burst Round
b.rnd
Adjust from
oFF, 2 ~ 10
Set stop voltage to
protect AEG battery
b.tyP
Adjust from
oFF, 5.0 ~ 9.0V
oFF is stop protect.
Bind a EGATE
bind
Exit to upper layer
EXit
Select memory slot
MEM
Select slot from
1 ~ 8
Bind a ScU to
selected memory slot
Reset CC
rSt
no
yES
Total shot
ttS
Show total shot number.
Valid from 0 to 9999
Show AEG battery
AEG.b
Show AEG battery volt
continuously.
(Need ScU)
Enter the boss role
boSS
Generate boss ID
?.?.?.?.
Stop fire
StoP
no
yES
on
oFF