Xcortech X3300W User Manual

CH-1. X3300W units
X3300SCU (optional): Shot Control Unit (SCU)
Controls burst mode through the by command
center. Module.
X3300CC : Command center control system.
A. Available in Black and Tan color.
B. Uses 2 x AA batteries.
X3300MF : Muzzle Flamer /Tracer Unit.
A. Available in Black Color
B. Uses 4 x AAA, Alkaline or Eneloop batteries
● X3300W install :
1. Install X3300MF on the reverse 14mm thread of AEG barrel ( Fig. 1)
2. Install X3300CC on your AEG’s tactical rail ( Fig. 1)
3. Connect the X3300SCU to the AEG’s Battery ( Fig. 2) - (optional).
4. Turn on the X3300MF and X3300CC power
5. Configure the X3300CC settings
6. X3300CC and X3300SCU need to be linked together after binding/pairing
7. X3300SCU controls burst mode with low-voltage protection (optional)
● X3300CC and X3300SCU binding /pairing:
1. Set the X3300CC “Mode Selector” to “ST”, rotate the “Data Wheel” to ScU
then push the “Data Wheel”, select to “MEM” and push the “Data Wheel”
2. In “MEM”, select Memory 1 ~ 8
Ex: Select “1” then “Data Wheel”
3. Rotate “Data Wheel” to select, “bind” will display “[ 1 ]”, in the “[ ]” flashing
4. Push X3300SCU switch on the PCB
5. X3300CC displays a “[ 1 ]” that will flash repeatedly, indicating settings are
complete
6. The X3300CC has 8 memory channels for binding/pairing
※ Reference “X3300W ScU shot control unit in Ch5
CH-2. Installation
X3300CC operation:
● Mode Selector:
1. ROF (roF) : Displays rate of fire (Rounds per-minute)
2. SPD (SPd) : Displays BB Velocity
3. DN (dn) : Display count down
4. UP (UP) : Display count up
5. 0 (oFF) : Power off
6. ST (SEt) : Set Command center
● Data Wheel (pushable): Rotate the “Data Wheel” to set the Data
1. In ROF/SPD/DN/UP mode :
A. Rotate “Data Wheel” : To adjust screen brightness
B. Push and hold 2sec : To reset UP and preset DN count.
C. Quickly push “Data Wheel” 3 times :
To select Burst/Auto firing mode (Display shows brSt / AUto
2. In ST mode :
A. Rotate “Data Wheel” : Select parameter or set it.
B. Push “Data Wheel” : To confirm the parameter.
● Display 4 Digits-Display
CH-3. X3300W Kits operation
X3300MF operation
● Power : ON/OFF
● Power indicator : Green light is running, Red light
indicates low battery
Unit will Auto power off if not used for 10 mins
● Inner barrel length to insert Max 40mm
X3300SCU operation
● Binding/pairing SW
** The X3300CC and X3300MF has paired in factory.
That can’t mix CC and MF with else.

Xcortech X3300W Specifications

General

Compatibility	Airsoft BBs
Detection Technology	Infrared
Power Source	Battery
Material	Plastic
Hit Indicator	LED Display
BB Speed Range	30 to 400 m/s

Summary

X3300W Units Overview

X3300CC Command Center

Command center control system, available in Black and Tan, uses 2 AA batteries.

X3300MF Muzzle Flamer/Tracer Unit

Muzzle Flamer/Tracer Unit, available in Black, uses 4 AAA batteries.

X3300W Installation Guide

X3300W Unit Installation Steps

Steps to install X3300MF, X3300CC on AEG barrel and tactical rail.

X3300CC and X3300SCU Binding/Pairing

Procedure for binding/pairing X3300CC with X3300SCU using the Data Wheel.

X3300W Kits Operation

X3300CC Operation Modes

Details on X3300CC modes: ROF, SPD, DN, UP, OFF, and SET command center.

X3300MF Operation

Describes X3300MF power ON/OFF and power indicator status.

X3300SCU Operation

Details X3300SCU binding/pairing switch functionality.

X3300CC Setup Operation

Flash Control (FLM)

Setup for flash control, enabling or disabling tracer BBs.

Boss Role (boSS)

Configure the boss role for team battle mode and BB count limits.

Count Down Setting (cnt)

Set the initial count down value from 5 to 9999.

Low Ammo Warning (WArn)

Set low ammo warning level from 1 to 100 or disable.

AEG Battery Display (AEG.b)

Display AEG battery voltage, requires SCU linkage.

Speed Unit (Unit)

Set the unit for speed measurement (M: Meter/sec, F: Feet/sec).

Auto Power Off (APO)

Set auto power off timer from 1 to 80 minutes.

Save Display Power (Eco)

Enable/disable power saving for screen brightness.

Total Shot Count (ttS)

Display total shot count, resettable by holding Data Wheel.

Shot Control Unit (ScU)

Setup burst round shot for the Shot Control Unit.

Factory Reset (rSt)

Reset the device to factory default settings.

X3300W SCU Setup

Burst Round Setting

Configure burst fire mode from OFF to 10 rounds.

Low Power Protection

Set low voltage level (5.0-9.0V) for battery protection.

Memory Slot Selection

Select memory slot from 1 to 8 for saving settings.

Binding SCU

Procedure for binding/pairing the SCU to the X3300W.