Xlerator XL - User Manual

XL
XleratorManual3-11.doc
FOR PROPER ELECTRICAL CONNECTIONS, CHECK YOUR LOCAL BUILDING CODES.
YOUR UNIT MUST BE INSTALLED BY A QUALIFIED, LICENSED ELECTRICIAN.
PARTS LIST FOR XLERATOR DRYER
REF NO.
DESCRIPTION
XL 1 Cover (includes Nameplate)
XL 2 Nameplate
XL 3 Tamper-proof Bolt
XL 4 Tamper-proof Wrench
XL 5 Air Outlet (includes gasket)
XL 6 Terminal Block (includes screws)
XL 7 Control Assembly & Sensor
XL 8 Heating Element Assembly
XL 9 Motor Assembly
XL 10 Wall Plate Assembly
XL 11 Cover Mounting Brackets
XL 12 Housing Grommet
XL 13 Housing Retainer
XL 14 Recess Kit (for ADA)
XL 15 Optics Assembly (Sensor)
NOTE
: Model, Serial Number and Voltage of the
dryer MUST BE included when ordering parts.
NOTE: Upon completing installation and checking for proper operation, it is highly recommended that a bead of silicone sealant be placed around
the outside of the cover at the wall to protect dryer from internal corrosion caused by wash water and cleaning solutions
INSTALLATION INSTRUCTIONS FOR XLERATOR® HAND DRYER
1. Remove cover of dryer by unscrewing two tamper-proof bolts from the sides of the cover with the special wrench provided with each unit.
2. Attach wall plate at the four corners to smooth wall. In locations where vandalism is a concern, use the two additional mounting holes shown.
Remove control assembly to access right side mounting hole. Attach with the recommended type of fastener (see above).
3. Connect a 110/120V dryer to a 15 Amp. dedicated branch circuit using at least #12 GA copper wire. (Do not exceed a 20 Amp. branch circuit)
Connect a 208, 220/240V or 277V dryer to no more than a 15 Amp. dedicated branch circuit using at least a #14 GA copper wire.
Attach lines to terminals as indicated by the schematic inside dryer cover. Be sure that an equipment ground wire is securely fastened to green
ground screw on base plate. Dryers should be installed per local code requirements.
4. In multiple installations, before replacing cover, check the Serial Number marked inside the dryer to be sure it matches the Serial Number marked
on the label at the bottom of cover. PLEASE DO NOT SWITCH COVERS. Do not forget to leave the special TAMPER PROOF WRENCH with
the owner.
Suggested Mtg. Heights from floor
to bottom of dryer
Men’s 45“ (1143 mm)
Ladies’ 43“ (1092 mm)
Teenagers’ 41“ (1041 mm)
Sm. Children 35“ (889 mm)
Handicapped 37“ (940 mm)
IF MOUNTING OVER COUNTERTOP, DISTANCE FROM
COUNTER TO DRYER MUST BE 15” (381mm) MINIMUM
Recommended Fastener
Masonry Wall ½” expansion sleeve with ¼” lag bolt
Hollow Wall ¼” wing type through bolt
Wooden Wall ¼” lag screw with washer
LOCATION OF ADDED MTG
HOLES FOR MORE SECURE
INSTALLATION
INSTALLATION NOTE: If the dryer will not turn on, stays on or stops working, it may be mounted too close to a counter or object. Turn off the
power to dryer for 10 seconds and then reapply power. If dryer will start, then turn off again, relocate the object or remount dryer. If this is not
possible, adjust the range of the sensor by turning the range adjustment on the control board, counterclockwise to decrease sensor range.
Please call the factory at 1-800-255-9235 and one of our trained technicians will be happy to assist you.
XL14
XL1
XL2
(Location)
XL3
XL4
XL5
XL6
XL7
XL8
XL9
XL10
XL11 (2)
XL12 (4)
XL13 (4)
XL15

Summary

Installation Instructions for Xlerator Hand Dryer

Suggested Mounting Heights

Specifies recommended installation heights from the floor for various user groups.

Recommended Fasteners

Lists appropriate fasteners for securing the dryer to masonry, hollow, or wooden walls.

Installation Steps and Notes

Covers cover removal, wall plate attachment, electrical connections, and serial number checks.

Parts List for Xlerator Dryer

Comprehensive list of all available replacement parts with reference numbers.

Cleaning and Maintenance

Outside Cleaning Instructions

Guidelines for washing the dryer's exterior with mild soap and water.

Inside Cleaning

Procedure for internal cleaning, to be performed by qualified service personnel.

Troubleshooting Your Dryer

Dryer Does Not Turn On

Steps to diagnose and resolve issues when the dryer fails to power on.

Dryer Does Not Shut Off

Troubleshooting steps for dryers that remain operational continuously.

Dryer Does Not Always Turn On or Turns On By Itself

Diagnosing intermittent operation or unexpected activation of the dryer.

Dryer Blows Cold Air

Steps to address issues where the dryer only outputs cold air.

Dryer Has Loss of Air Volume

Procedure for diagnosing and resolving reduced airflow from the dryer.

Warranty Information

5-Year Limited Warranty

Details the terms, conditions, and remedies for the product's five-year warranty.

Xlerator XL Specifications

General

Type	Hand Dryer
Frequency	50/60 Hz
Amperage	12.5A at 120V, 6.25A at 240V
Air Speed	16, 000 ft/min
Drying Time	8 Seconds
Sound Level	80 dB
Activation	Automatic Sensor