Xtralis VPS-215-E - User Manual

Xtralis Power Supplies VPS-215-E & VPS-220-E Installation and Commissioning Instructions
www.xtralis.com Approved Document No. DFU0002150 Rev 3 www.xtralis.com Page 1 of 2
VPS-215-E & VPS-220-E are power supply units (PSU) for Xtralis Aspirating Smoke Detectors (ASD).
They are compliant with EN54-4:1997+A1:2002+A2:2006.
Xtralis VPS-215-E
(0.5A load, 7Ah max)
and
Xtralis VPS-220-E
(0.5A load, 14Ah max)
1
Location: Site the PSU indoors on a dry, flat surface in an area that is well ventilated. Where possible the panel’s indicators (internal and
external) should be at eye level and the unit should be installed in the same location as the ASD it powers.
2
Knockouts: Before mounting, remove selected knockouts with a sharp light tap, using a flat broadsided screwdriver (shown right). Fill knockout
holes with good quality cable glands.
3
Mounting: Mount the metal base securely onto a wall using the four mounting holes provided. Assess the condition and construction of the wall
and use No.8-10, or 4-5mm screws. Use the fixing hole template overleaf as a guide.
4
Wiring: Connect all AC cables BEFORE applying power. Maintain segregation between AC and DC cabling. All wiring should be installed in
accordance with relevant national standards, e.g. IEE Wiring Regulations BS7671 in the UK. Connect the incoming AC to CONN1 (② shown
overleaf) and ensure that earth straps are connected to the earth tag (shown right).
5
Connect DC: Connect the DC output to the Xtralis detector. Examples for the VESDA VLC, VLP and VLF are shown below which may use the General Purpose Input (GPI) to transmit the PSU
fault signal. The VESDA detector must be configured to interpret the GPI input as a ‘Mains OK’ if this feature is used.
6
Connect Batteries: Secure the batteries using battery straps and connect as shown. With charged batteries the DC output ⑧ will turn on, the OK LED will illuminate and the Fault LED will also
illuminate (as there is no AC input).
CAUTION: Only use good quality sealed Valve Regulated Lead Acid (VRLA) batteries. There is a risk of explosion if the batteries are replaced by incorrect types.
7
Commissioning: Switch on the AC supply to the PSU. The OK LED should stay lit and the Fault LED should turn off.
Check the fault relay is energized (short circuit between C and NO terminals
⑪
). Switch off the AC supply and confirm correct
operation of LEDs and relay – see table right. Restore the AC supply. Disconnect the batteries and confirm correct operation of
LEDs and relay – see table right.
8
Normal Operation/Fault Finding: The table in Step 7 provides a summary of the normal operation of the PSU when the battery and/or AC supply fails. When the AC supply fails, the DC output
is maintained for at least 24 hours as long as the batteries are in good condition. Damage to the batteries as a result of deep discharge is prevented by turning the DC output off (load shed mode)
when the battery voltage falls below approximately 21V. Should this happen the DC output will not be restored until the AC supply is re-established OR fully charged batteries have been installed.
However, the terminal voltage of the discharged batteries measured after the PSU has entered load shed mode may be greater than 21V because the voltage can recover when the battery is not
under load. Never leave the batteries connected for prolonged periods without an AC supply connected because, during load shed mode, there is a monitoring current Imin (<12mA) which, over
several days, will drain the batteries to the point they are damaged.
AC
Batteries
OK
LED
Fault
LED
Fault
relay
Fault terminals
ON
OK (Healthy)
ON
OFF
ON
NO-C=short
OFF
ON
ON
OFF
NC-C=short
ON
Not OK
(Discharged or
Disconnected
or Faulty)
ON
ON
OFF
NC-C=short
OFF
OFF
OFF
OFF
NC-C=short

Summary

Installation Location and Mounting

Location

Site the PSU indoors on a dry, flat surface in a well-ventilated area at eye level.

Mounting

Mount the metal base securely onto a wall using provided mounting holes and appropriate screws.

Wiring and Connections

Knockouts

Remove selected knockouts with a sharp tap and fill holes with quality cable glands.

Wiring

Connect AC cables BEFORE power, maintain segregation, connect incoming AC to CONN1, ensure earth straps.

Connect DC

Connect the DC output to the Xtralis detector, configure detector for Mains OK signal if using GPI.

Power Supply Setup and Commissioning

Connect Batteries

Secure batteries using straps and connect; DC output turns on with charged batteries.

Commissioning

Switch on AC, check OK LED and Fault LED, verify fault relay operation, disconnect/reconnect batteries.

Normal Operation and Fault Finding

Understand PSU operation during AC/battery failure, load shed mode, and battery damage prevention.

Xtralis VPS-215-E Specifications

General

Input Voltage	100-240 VAC
Input Frequency	50/60 Hz
Output Voltage	24 VDC
Output Current	5 A
Protection	Overload, Short Circuit, Over Voltage
Certifications	CE, UL
Storage Temperature	-20°C to +70°C (-4°F to +158°F)