Need help?Do you have a question about the XTZ 99.36 MKII Walnut and is the answer not in the manual?
General| Weight | 24 kg |
|---|---|
| Power Handling | 300 W |
| Finish | Walnut |
| Type | 3-way, bass reflex |
| Impedance | 4-8 Ohm |
| Dimensions | 200 x 950 x 320 mm |
| Recommended Amplifier | 50-300W |
| Woofer | 1 x 6.5 inch |
Our reference and starting point is to create a natural sound, considering acoustics is a matter of taste.
Our main goal is to provide the best value for money through cost-effective manufacturing and product quality.
Website: www.xtz.se E-mail: info@xtz.se
The box design with a narrow baffle and curved side provides acoustic advantages by suppressing internal resonances.
Features a ribbon tweeter with superior transient response and a flat frequency response, made with a lightweight sandwich construction.
Uses a 6.5" magnesium driver from the Seas Excel series, known for extreme performance and a light, stiff cone.
Features a 6.5" SEAS coated paper driver, known for being light, stiff, and reducing resonances effectively.
Utilizes a -12/18 dB crossover with gold-plated bi-wiring type connectors for various coupling modes.
Carefully unpack the speaker, save the box for future transport. Contact your retailer if any damage occurs.
The package includes Bass reflex plugs (6 pcs), User manual, and Loops for level adjustment (6pcs).
Achieving the best sound depends on the listening environment; improper setup can make even good equipment sound bad.
Carpets and soft furniture absorb sound; empty areas produce hard reflections that can distort sound perspective.
Placement near walls amplifies bass. Keep speakers at least 30cm from walls for clear sound reproduction.
Be aware that furniture may vibrate and cause unwanted noise at high volume levels.
Avoid quadratic rooms or rooms where length is twice the width to prevent unwanted resonance issues.
Subwoofer placement significantly affects frequency response. Patience and experimentation are needed for optimal results.
Keep cables short, ensure clean connections, and separate signal cables from power and loudspeaker cables.
Place front speakers symmetrically, 80% of listener distance apart, with a recommended angle of 45°.
Using two subwoofers increases maximum sound pressure level and improves room frequency response.
Good sound is subjective; experiment to find your preferred sound. Good luck with your setup!
Speakers are typically placed standing by a wall. Wall proximity affects bass level; experiment with distances.
Always connect with correct phase (+ to +, - to -). Incorrect phase affects sound, especially low frequencies.
Be cautious of overloading drivers and amplifier at high loads. Avoid extreme volume and excessive EQ boosts.
Drivers require 50-100 hours of initial playing time to reach optimal sound. Use normally during this period.
Use bass plugs in reflex gates to adjust lower boundary frequency. Settings depend on room size and personal taste.
Achieve deepest bass with one plug in the lower gate, suitable for smaller rooms. Bass level at mode 2 (+3dB).
Use without bass plugs for a 'quick' bass, ideal for large rooms where bass frequencies are often amplified.
Achieve a flat frequency response with two plugs in the gates. Bass level set at mode 1 (0dB).
No single neutral setting suits all rooms. Factors like room, placement, and output levels influence sound.
Treble level is adjustable in four modes (0dB, +3dB, -2dB, -4dB) using a loop connector for sonic tuning.
Bass level is adjustable in four modes (0dB, +3dB) using a loop connector for flat response or boost.
Default setting uses all terminals. Without loops, terminals can be used for tweeter, midrange, or woofer only.
2 1/2-way with separate boxes. Bass reflex cabinet configurable to closed box with eight distinct bass modes.
Dimensions are 244 x 910 x 352 mm (Width x Height x Depth).
The weight of each speaker is 19.5 kg.
The speakers are not magnetically shielded.
The impedance rating for the speakers is 4-8 ohm.
Features gold plated bi-wiring, Banana plug, and Pole screw binding posts.
The speaker efficiency is rated at 88dB.
Power handling is 550 W Short term IEC 268-5 and 200 W Long term IEC 268-5.
Ribbon tweeter, SACD/DVD-Audio-ready, with sandwich ribbon cone and neodymium magnets.
6.5" SEAS Excel Magnesium driver with 'high flow' basket and powerful magnet, weighing 1900 grams.
6.5" SEAS coated paper driver with 'high flow' basket and powerful magnet, weighing 1900 grams.
Gold plated biwiring, bass reflex (8 modes), adjustable treble (4 modes), and adjustable bass (4 modes).
XTZ promotes 'do-it-yourself' service for parts. Contact us before dismounting if unsure about the process.
Warranty applies for manufacturing defects. It does not apply if user causes additional damage when dismounting.
Refer to retailer for service. Pack product carefully to avoid transport damage. Enclose receipt and defect description.
Contact free support for installation advice or problems via email at support@xtz.se for assistance.
To Next Page
